Emerson Bettis RTS FQ Series Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 91

background image

4

Section 3: General

User Instructions

MAN-02-04-60-0351-EN Rev. 3

Febraury 2019

General

Section 3: General

3.1

Safety Instructions

CAUTION: FOLLOW SAFETY INSTRUCTIONS

When operating electrical devices, certain parts are inevitably under dangerous voltage.
Work on the electrical systems or components may only be carried out by electricians or by
individuals who have been instructed how to do so, working under the guidance and
supervision of an electrician in accordance with electrotechnical regulations.

WARNING: ALWAYS REFER TO STANDARDS

When working in potentially explosive areas, refer to European Standards EN 60079-14
“Installing Electrical Systems in Explosion Endangered Areas” and EN 60079-17 “Inspection and
Maintenance of Electrical Installations in Explosion Endangered Areas”.
Working in potentially explosive areas is subject to special regulations (European Standard EN
60079-17), which must be complied with. Any additional national regulations must be heeded.

CAUTION: ALWAYS BE AWARE OF DANGER TO EXPLOSION

Work on the open actuator under voltage may only be done if it is certain that there is no
danger of explosion for the duration of the work.

3.2

Serial Number

Each actuator of the Bettis RTS FQ Series carries a serial number. The serial number is a
10-digit number that begins with the year and that can be read from the type label
(see Figure 3) the type label is located next to the handwheel).

Using this serial number, Bettis can uniquely identify the actuator (type, size, design,
options, technical data and test report).

3.3

Protection Class

Bettis RTS FQ Fail-Safe Quarter-Turn actuators come by default with IP 68
(EN 50629) protection.

CAUTION:

The protection class specified on the type label is only effective when the cable

glands also

provide the required protection class, the cover of the connection compartment
is carefully secured closed, and the mounting position (see Section 3.4) is observed.

«
...
7
8
9
10
11
...
»

Содержание Bettis RTS FQ Series




























































































Отзывы:

Нет отзывов

Похожие инструкции для Bettis RTS FQ Series

Бренд: ABB Страницы: 30

Бренд: ABB Страницы: 15

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 44

Бренд: FAAC Страницы: 12

Бренд: Watts Страницы: 2

Бренд: Hanbay Страницы: 18

Бренд: BabySafe Страницы: 24

Бренд: Campbell Страницы: 3

Бренд: JENCO Страницы: 36

Бренд: jcm-tech Страницы: 8

Бренд: Saftronics Страницы: 13

Бренд: Watlow Страницы: 59

Tekmar WiFi Snow Melting Control 670

Бренд: Watts Страницы: 48

Бренд: B&G Страницы: 19

Бренд: Universal Remote Страницы: 20

Бренд: Aulisa Страницы: 32

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды