Emerson Bettis RTS FQ Series Скачать руководство пользователя страница 52

Страница: 52 / 91

Section 8: Parameter Menu

User Instructions

MAN-02-04-60-0351-EN Rev. 3

February 2019

Parameter Menu

Table 16.

Binary Outputs Parameter Group (3)

Menu

Item

Sub Menu
Item

Poss. Setting

Notes / Comments

P10.1

Binary
Output

Output 1

47: Pos.=Int2

Position = Intermediate position 2. The width of the
interval is set with the parameter P8.6.

48: Pos.=Int3

Position = Intermediate position 3. The width of the
interval is set with the parameter P8.6.

49: Pos.=Int4

Position = Intermediate position 4.The width of the
interval is set with the parameter P8.6.

50:
Pos.=EmergPos

Position = emergency position. The width of the interval
is set with the parameter P8.6.

51: Bus Bit 1

In existing bus interface (hardware option) the output is
set according to the selected bit bus.

52: Bus Bit 2
53: Bus Bit 3
54: Bus Bit 4
55: Bus Bit 5
56: Bus Bit 6
57: Bus Bit 7
58: Bus Bit 8

59: Virtual 1

Configurable output function

60: Virtual 2

61: Virtual 3

62: Virtual 4

63: Line
voltage OK

Supply voltage for the motor is OK

64: Control
voltage OK

The auxiliary voltage for the SMARTCON control is
OK. This function is only available if the auxiliary
voltage output is not switched on (P6.5 to 0).

65: Oil pressure
OK

The oil pressure is higher than the minimum
pressure (P6.10).

66: Oil level OK The oil level is OK.

67: Pump OK

The temperature sensor in the pump motor and the
external motor protection have not tripped.

4-5
P10.2

Binary
Output

Output
conf. 1

0: Normal

Output 1 is set to normal, i.e. if the condition in
point P10.1 is met, Output 1 is set to HIGH (active
HIGH).

1: Inverted

If the condition in point P10.1 is met, Output 1 is set
to LOW (active LOW).

2: Norm.
flashing

If the condition in point P10.1 is met, Output 1
starts blinking (active HIGH).

3: Inv. flashing

If the condition in point P10.1 is not met, Output 1
starts blinking (otherwise it is set to HIGH).

P10.3

Bin. Output Output 2

see Output 1

P10.4

Bin. Output

Output 2
conf.

see Output 1
conf.

P10.5

Bin. Output Output 3

see Output 1

P10.6

Bin. Output

Output 2
conf.

see Output 1
conf.

P10.7

Bin. Output Output 4

see Output 1

Содержание Bettis RTS FQ Series




























































































Результаты поиска

Содержание Bettis RTS FQ Series

Отзывы:

Похожие инструкции для Bettis RTS FQ Series

Бренды по названию

Популярные бренды

Emerson Bettis RTS FQ Series, Руководство по эксплуатации

Результаты поиска

Содержание Bettis RTS FQ Series

Отзывы:

Похожие инструкции для Bettis RTS FQ Series

Бренды по названию

Популярные бренды