Emerson Bettis RTS FQ Series Скачать руководство пользователя страница 35

Страница: 35 / 91

Section 7: Control Unit

User Instructions

MAN-02-04-60-0351-EN Rev. 3

Febraury 2019

Control Unit

Figure 38

Halfway Switch Flip (it will jump to the next parameter category)

Figure 39

Full Switch Flip (it will jump to the end of the menu)

7.3.1 Operation Mode

Use the selector switch (red) to determine the various operating states of the actuator. In
each of these positions, it is possible to block the switch by means of a padlock and thus
protect the actuator against unauthorized access.

The selector switch has the following positions:

Table 3.

Operating Mode Table

OFF

The actuator can be neither operated via the remote
control nor via the control switches of the controller.

Local

It is possible to operate the actuator by motor via the control

switch. Control via the remote inputs may be possible with

appropriate configuration (superimposed control commands,

emergency commands).

Remote

The actuator is ready to process control commands via input

signals. The control switch for the motor operation of the

actuator is not enabled.

Besides defining the operational status, the selector switch is used in configuration mode
to confirm or cancel parameter inputs.

Depending on the selector switch position, the control switch performs different functions:

Содержание Bettis RTS FQ Series




























































































Результаты поиска

Содержание Bettis RTS FQ Series

Отзывы:

Похожие инструкции для Bettis RTS FQ Series

Бренды по названию

Популярные бренды

Emerson Bettis RTS FQ Series, Руководство по эксплуатации

Результаты поиска

Содержание Bettis RTS FQ Series

Отзывы:

Похожие инструкции для Bettis RTS FQ Series

Бренды по названию

Популярные бренды