26
Threading Loopers with the Looper Threading
Wire or Standard Thread
If the looper threads are made from materials that are
difficult to thread, such as wooly nylon, there are 2
ways to thread the looper threads:
• Use the looper threading wire (looper threader)
• Tie the thread to standard thread, which you then
use to thread.
q
q
w
e
r
t
t
z x
c
v b
n m
,
Turn the power switch OFF before threading the
machine.
Using the looper threading wire
z
Pass the thread up to the looper thread guide (before
the looper threader hole).
x
Set the looper threader switch lever to the
“THREADING” position.
q
Looper threader switch lever
c
Turn the handwheel toward you slowly until it clicks.
This locks the handwheel in place.
w
Handwheel
v
Pass the straight end (not the loop end) through the
looper threader hole until it comes out from the the
hole of the looper tip.
e
Loose end of looper threading wire
r
Looper threader hole
b
Pass approximately 2˝ (5 cm) thread through the loop
of the looper threading wire.
t
Thread
n
Pull the loose end of the looper threading wire until
the thread comes out from the hole of the looper tip.
m
Remove the thread from the looper threading wire.
,
Return the looper threader switch lever to the
“SEWING” position.
CAUTION
Do not raise or lower the looper thread lever while
threading.
Provlačenje donjeg konca žicom za uvlačenje
ili standardnim koncem
Ako je donji konac od materijala koji se teško uvlači,
kao što je najlon ili vuneni najlon, možete ga na 2
načina uvući:
Koristite žicu za uvlačenje konca
Zavežite ga za standardni konac, koji ćete onda
iskoristiti za provlačenje.
PAŽNJA
PAŽNJA
Pre provlačenja konca, isključite glavni prekidač
na mašini.
Nemojte podizati niti spuštati polugu za uvlačenje
konca tokom provlačenja.
Upotreba žice za uvlačenje
Provucite konac kroz vodič donjeg konca (sve do
pred otvor uvlakača konca petljača).
Postavite ručicu prekidača na poziciju
"PROVLAČENJE KONACA".
Ručica prekidača uvlakača donjeg konca
Okrenite polako zamajac ka sebi dok ne klikne.
Na ovaj način ste blokirali zamajac.
Zamajac
Provucite ravan kraj (ne omču) kroz otvor uvlakača
donjeg konca dok ne izviri iz otvora na petljaču.
Slobodan kraj žice za uvlačenje konaca
Otvor uvlakača donjeg konca
Provucite približno 5 cm konca kroz omču na žici
za uvlačenje donjeg koca.
Konac
Povucite slobodan kraj žice za provlačenje konca
sve dok konac ne izađe iz otvora na na vrhu
petljača.
Uklonite konac iz žice za provlačenje donjeg konca.
Vratite ručicu prekidača uvlakača donjeg konca
u položaj "ŠIVENJE".
Содержание eXtend 864air
