ELNA eXtend 864air, Руководство пользователя

Страница: 29 / 64

27
Using a standard thread
z
Pass the thread up to the looper thread guide (in front
of the looper threader hole).
q
Looper thread
x
Prepare 12˝ (30 cm) of a standard thread and tie it 5
cm from the end of the looper thread as shown.
w
Standard thread
e
Knot
r
5 cm
t
c
y
v
u
i
b
Figure A
e
c
t
,
q
m
q
w
e
z x
q
w
e
r
x
o
n
q
z
q
NOTE:
when tying the standard thread to the looper thread,
tie a knot as small as possible and cut any excess
standar thread.
c
Set the looper threader switch lever to “THREADING”
position.
t
Looper threader switch lever
v
Turn the handwheel toward you slowly until it clicks.
This locks handwheel in place.
y
Handwheel
b
Using the tweezers, insert approximately 1˝ (2 cm) of
the standard thread into the threading hole.
u
Tweezers
i
Looper threader hole
n
Raise the looper threader lever until it clicks into
place.
Lower the looper threader lever until it knocks into
place.
o
Looper threader lever
m
Pull out approximately 4˝ (10 cm) of the standard
thread from the hole in the looper tip and trim it at the
knot.
* When the knot reaches the looper threader hole,
fold the loose end of the looper thread as illustrated
by figure A in procedure
b
.
,
Return the looper threader switch lever to the
“SEWING” position.
Replacing threaded looper thread
z
Cut the threaded looper thread between the thread
guide and the top cover thread guide.
q
Thread guide
w
Top cover thread guide
x
Set a new spool of looper thread.
Pass the new looper thread through the thread guide,
and tie it to the end of the threaded looper thread.
Tie a knot as small as possible.
e
Knot
c
Slowly pull the threaded looper thread out from the
hole of the looper tip until the knot comes out.
Upotreba standardnog konca
Provucite konac kroz vodič donjeg konca (sve do
pred otvor uvlakača konca petljača).
Donji konac
Proptrmite 30 cm standardnog konca i zavežite ga
5 cm od kraja donjeg konca, kao što je prikazano.
Standardni konac
Čvor
5 cm
NAPOMENA:
Kada standarni konac vezujete za donji konac,
napravite što je moguće manji čvor i odsecite
ostatak standardnog konca.
Postavite ručicu prekidača uvlakača konca u
položaj "PROVLAČENJE KONCA".
Ručica prekidača uvlakača konca
Okrenite polako zamajac ka sebi dok ne klikne.
Na ovaj način ste blokirali zamajac.
Zamajac
Pincetom ubacite približno 2 cm standardnog
konca u otvor za provlačenje.
Pinceta
Otvor za provlačenje donjeg konca
Podignite polugu uvlakača donjeg konca dok
ne ulegne u ležište.
Spustite polugu uvlakača donjeg konca dok
ne ulegne u ležište.
Poluga uvlakač donjeg konca
Izvucite približno10 cm standardnog konca iz
otvora na vrhu petljača i odsecite ga do čvora.
Kada čvor dosegne otvor na petljaču konca,
presavijte slobodan kraj standardnog konca kao
na ilustraciji A koraka
Ilustr.
Vratite ručicu prekidača uvlakača donjeg konca
u položaj "ŠIVENJE".
Zamena donjeg konca
Presecite donji konac između vodiča konca i
usmerivača konca na gornjem poklopcu mašine.
Vodič konca
Usmerivač konca
Postavite novi kalem donjeg konca.
Provucite novi konac kroz vodič, i vežite ga za
kraj provučenog konca.
Napravite što je moguće manji čvor.
Čvor
Lagano povucite prethodno provučeni konac
kroz vodič gornjeg konca dok čvor ne izađe
kroz otvor na vrhu petljača.