Elite Greenhouses 6'3" WIDE HIGH EAVE Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 32

background image

FINISHING OFF

To prevent the door from sliding past its opening, you must fix 2 angle brackets to the door end as-
sembly.

Insert a cropped head bolt into the bolt channel at the top of the left hand glazing bar (viewed from
the inside) and fix and angle bracket as shown in the picture below.
The bracket must be fitted at the same height as the door panel so that, as the door moves left or
right, the bracket prevents the door from moving too far along the top door track.
Repeat at the bottom of the door.

«
...
16
17
18
19
20
...
»

Содержание 6'3" WIDE HIGH EAVE

































Отзывы:

Нет отзывов

Похожие инструкции для 6'3" WIDE HIGH EAVE

essential Series

Бренд: Gabriel Ash Страницы: 43

Бренд: G-Tools Страницы: 12

Бренд: Sproutwell Страницы: 32

Бренд: Polytunnel Company Страницы: 15

Бренд: Palram Страницы: 12

Бренд: ACD Страницы: 62

Deuba 4250525324167

Бренд: Gardebruk Страницы: 25

Бренд: Gardebruk Страницы: 47

Deuba 4250525324136

Бренд: Gardebruk Страницы: 53

Бренд: EINHELL Страницы: 48

2X3M MEDIUM CAGE

Бренд: Feel Good Страницы: 7

Бренд: Norfolk Greenhouses Страницы: 36

Бренд: One Stop Gardens Страницы: 4

ONE STEP GARDEN 92050

Бренд: One Stop Gardens Страницы: 7

Бренд: One Stop Gardens Страницы: 7

Бренд: One Stop Gardens Страницы: 8

Бренд: Outsunny Страницы: 4

Бренд: Outsunny Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды