Electrolux EXH09HL1W Скачать руководство пользователя страница 17

Страница: 17 / 62

210-10 ADL

17/62

599 75 60-77

Electrical Work:

CAPACITY

POWER SUPPLY

INPUT RATED AMP

Switch/Fuse

CABLE SIZE

EXH09HL1W
EXH12HL1W

220-240V~/50Hz

16A/16A

1.5 mm

(power cord)

1.5 mm

(connecting cable)

Connect the Cable to the Indoor Unit

（

instruction manual

）

1.The inside and outside connecting cable can be

connected without removing the front panel.

2. Connecting cable between indoor unit and outdoor unit

shall be approved polychloroprene sheathed flexible

cord,type designation H07RN-F or heavier cord.

3.Life the indoor unit panel up,remove the electrical

box cover by loosening the screw.

4.Ensure the colour of wires of outdoor unit and the

terminal Nos. are the same to the indoor respectively.

5.Wrap those cables not connected with terminals with

insulation tapes,so that they will not touch any electrical

components.Secure the cable onto the control board

with the cord clamp.

Connect the Cable to the Outdoor Unit

1.Remove the electrical control board cover from the

outdoor unit by loosening the screw.

2.Connect the connective cables to the terminals as

Identified with their respective matched numbers on

the terminal block of indoor and outdoor unit.The connective

cable to power supply shall be approved polychloroprene sheathed flexible

cord,type designation H07RN-F or heavier cord.

3.Securd the cable onto the control board with the cord

clamp.

4.To prevent the ingress of water,form a loop of the connective

cable as illustrated in the installation diagram of indoor and outdoor

units.

5.Insulate unused cord(conductors) with PVC-tape.Process them so

they could not touch any electrical or metal parts.

Содержание EXH09HL1W































































Результаты поиска

Содержание EXH09HL1W

Отзывы:

Похожие инструкции для EXH09HL1W

Бренды по названию

Популярные бренды

Electrolux EXH09HL1W, Руководство по обслуживанию

Результаты поиска

Содержание EXH09HL1W

Отзывы:

Похожие инструкции для EXH09HL1W

Бренды по названию

Популярные бренды