Electrolux EXH09HL1W Скачать руководство пользователя страница 18

Страница: 18 / 62

210-10 ADL

18/62

599 75 60-77

7. Electronic Function

1.Temperature Parameters

◆

Indoor preset temperature (Tpreset)

◆

Indoor ambient temperature (Tamb.)

2.Basic Functions

(The temperature in this manual is expressed by Centigrade. If Fahrenheit is used, the switchover between

them is Tf=TcX1.8+32.)

Once the unit is energized, the compressor shall never be restarted except 3mins interval at least. For the first energization, if

the unit is at off status before power failure, the compressor can be restarted without 3-min delay. But if the unit is at ON status

before power failure, the compressor shall be restarted with 3mins delay. Once the compressor is started up, the compressor

won't stop running within 6mins with the change of room temperature.

(1)Cooling Mode

①

Cooling Conditions and Process

When Tamb.

≥

Tpreset, the unit starts cooling operation. In this case, the compressor and the outdoor fan operate and the

indoor fan operates at set speed.

When Tamb. ≤Tpreset-3

℃

, the compressor and the outdoor fan stop while the indoor fan runs at set speed.

When Tpreset-3

℃

＜

Tamb.

＜

Tpreset, the unit will maintain its previous running status.

In cooling mode, the temperature setting range is 16

～

℃

; Indoor unit displays operation icon, cooling icon and set

temperature.

(2) Dry Mode

①

Drying Conditions and Process

When Tamb.>Tpreset, the unit operates in cooling mode. Meanwhile, compressor and outdoor fan operate, and indoor fan

operates at set fan speed (low fan speed, quiet fan speed).

When Tpreset-3

℃＜

Tamb.

≤

Tpreset, the unit keeps previous operation status.

When Tamb.

≤

Tpreset-3

℃

, compressor, outdoor fan and indoor fan operate at set fan speed (low fan speed, quiet fan speed).

Under this mode, the temperature setting range is 16

～

℃

. Display displays operation icon, drying icon and set temperature.

Содержание EXH09HL1W































































Результаты поиска

Содержание EXH09HL1W

Отзывы:

Похожие инструкции для EXH09HL1W

Бренды по названию

Популярные бренды

Electrolux EXH09HL1W, Руководство по обслуживанию

Результаты поиска

Содержание EXH09HL1W

Отзывы:

Похожие инструкции для EXH09HL1W

Бренды по названию

Популярные бренды