elco AEROTOP T Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 54

elco AEROTOP T Скачать руководство пользователя страница 39

System

Sensor Characteristics NTC 1 k
Sensor Characteristics NTC 10 k

T

[°C] R[Ohm] T

[°C] R[Ohm] T

[°C] R[Ohm]

-30.0 13'034 0.0  2'857 30.0  827
-29.0 12'324 1.0  2'730 31.0  796
-28.0 11'657 2.0  2'610 32.0  767
-27.0 11'031 3.0  2'496 33.0  740
-26.0 10'442 4.0  2'387 34.0  713
-25.0 9'889  5.0  2'284  35.0  687
-24.0 9'369  6.0  2'186  36.0  663
-23.0 8'880  7.0  2'093  37.0  640
-22.0 8'420  8.0  2'004  38.0  617
-21.0 7'986  9.0  1'920  39.0  595
-20.0 7'578 10.0 1'840 40.0  575
-19.0 7'193 11.0 1'763 41.0  555
-18.0 6'831 12.0 1'690 42.0  536
-17.0 6'489 13.0 1'621 43.0  517
-16.0 6'166 14.0 1'555 44.0  500
-15.0 5'861 15.0 1'492 45.0  483
-14.0 5'574 16.0 1'433 46.0  466
-13.0 5'303 17.0 1'375 47.0  451
-12.0 5'046 18.0 1'320 48.0  436
-11.0 4'804 19.0 1'268 49.0  421
-10.0 4'574 20.0 1'218 50.0  407

-9.0 4'358 21.0 1'170

-8.0 4'152 22.0 1'125

-7.0 3'958 23.0 1'081

-6.0 3'774 24.0 1'040

-5.0 3'600 25.0 1'000

-4.0 3'435 26.0 962

-3.0 3'279 27.0 926

-2.0 3'131 28.0 892

-1.0 2'990 29.0 859

Sensor Characteristics 1K

for Exterior Temperature Sensor B9

T

[°C] R[Ohm] T

[°C] R[Ohm] T

[°C] R[Ohm]

-30.0 175203  50.0  3605  130.0  298
-25.0 129289  55.0  2989  135.0  262
-20.0 96360  60.0  2490  140.0  232
-15.0 72502  65.0  2084  145.0  206
-10.0 55047  70.0  1753  150.0  183

-5.0 42158 75.0 1481 155.0 163

0.0 32555 80.0 1256 160.0 145
5.0 25339 85.0 1070 165.0 130

10.0 19873 90.0 915 170.0 117
15.0 15699 95.0 786 175.0 105
20.0 12488

100.0 677 180.0 95

25.0 10000

105.0 586 185.0 85

30.0 8059 110.0 508 190.0  77
35.0 6535 115.0 443 195.0  70
40.0 5330 120.0 387 200.0  64
45.0 4372 125.0 339

Sensor Characteristics NTC 10 k

for Sensors B1, B3, B4, B21, B41, B71, B81, B91, and B92

39

«
...
37
38
39
40
41
...
»

Содержание AEROTOP T























































Отзывы:

Нет отзывов