Efka AB600A5015 Скачать руководство пользователя

Страница: 20 / 64

- AB600A5015

Instruction Manual

- 20 -

6.15.1 Set and Reset Operating Hours Counter

The number of hours has been reached (service necessary):



Press the

key once



The operating hours counter is set to "0" and restarted.

The number of hours has not yet been reached:



Press the

key three times



The operating hours counter is set also to "0" and
restarted.

A value in parameter 177 has been changed:



After displaying

rES ...,

when the

key is pressed again,

SEt

will then be displayed.



If the changed value is to be saved, press the

key 3 times.

6.15.2 Total Operating Hours Display

In this service routine enabled using parameter

176

, the total number of operating hours is displayed.

The sequence of displayed values is as with parameter

177

The values can only be displayed, not varied. Therefore, letter symbols "rES" for "reset" and "SEt" for "set"
will not appear.

Functions

7.1 Softstart

Function

Parameters

Softstart On/Off

(SSt)

134

Functions:



After power on



At the beginning of a new seam



Speed pedal controlled and limited to (n6)



Lower speed of a parallel function prevailing (e. G. Stitch count)



Stitch counting synchronized to position 1



Suspension with pedal in position 0 (neutral)



Interruption by full heelback (position -2)

7.1.1 Softstart speed

Function

Parameters

Softstart speed

(n6)

115

7.1.2 Softstart stitches

Function

Parameters

Number of softstart stitches

(SSc)

100

Содержание AB600A5015

































































Результаты поиска

Содержание AB600A5015

Отзывы:

Похожие инструкции для AB600A5015

Бренды по названию

Популярные бренды

Efka AB600A5015, Руководство по эксплуатации

Результаты поиска

Содержание AB600A5015

Отзывы:

Похожие инструкции для AB600A5015

Бренды по названию

Популярные бренды