Efka AB600A5015 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 64

background image

- AB AB600A5015

Instruction Manual

- 23 -

7.5 Machine run blockage

A

TTENTION

This is not a safety function. The line voltage must still be switched off during maintenance and
repair work.

The function “machine run blockage” is enabled by connecting a switch to socket B3, depending on the pre-
selection of parameter

240

Display after enabling machine run blockage without control panel:

Control display



Machine run blockage in the free seam, seam with stitch counting and light barrier seam:
The seam is suspended by opening and/or closing the switch.



Stop in the basic position



Needle up is not possible



Sewing foot lifting is possible

New start after machine run blockage

Function

Parameter

New start after machine run blockage

(Pdo)

234

Parameter 234

determines how a new start is possible after closing and/or opening the switch.

234 = 0

New start after disabling machine run blockage without influence by the pedal. This setting is
applicable, for example, to automats.

234 = 1

New start after disabling machine run blockage only if the pedal is in position 0 (neutral).

7.6 Thread trimming operation

Function

Parameters

Thread trimmer On/Off
Thread wiper On/Off

FA
FW

013
014

7.6.1 Thread Trimmer/Thread Wiper (Lockstitch Modes)

Function

Parameters

Thread wiper time

Thread wiper switch-on delay

Stop time for thread trimmer

(t6)

(dFw)

(tFA)

205

209

253

Thread trimming in the lockstitch modes is performed at trimming speed.
When the thread trimmer is off, the drive stops in position 2 at the seam end; it stops in position 1 at the end of
programmed seams.
The thread wiper ON period can be set depending on the selected trimming mode (see chapter "Timing
Diagrams" in the List of Parameters). The delay time (t7) (Parameter

206

) prevents sewing foot lifting before the

thread wiper is in its initial position.
If the thread wiper is not connected, there will be a delay time (tFL) after thread trimming until sewing foot lifting.

7.6.2 Trimming speed

Function

Parameters

Trimming speed

(n7)

116

A 2

«
...
21
22
23
24
25
...
»

Содержание AB600A5015

































































Отзывы:

Нет отзывов

Похожие инструкции для AB600A5015

Бренд: Fancom Страницы: 31

Бренд: 3M Страницы: 90

Бренд: Febco Страницы: 12

Бренд: HANYOUNG NUX Страницы: 36

Бренд: HANYOUNG NUX Страницы: 4

Бренд: MADRIX Страницы: 91

Бренд: MADRIX Страницы: 36

Бренд: MADRIX Страницы: 40

Бренд: YASKAWA Страницы: 18

Бренд: nekos Страницы: 8

Бренд: nekos Страницы: 8

Бренд: Neles Страницы: 12

Бренд: Aulisa Страницы: 32

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 26

Бренд: Beckhoff Страницы: 30

Бренд: Festo Страницы: 109

Бренд: Topworx Страницы: 8

Бренд: Bentel Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды