- AB AB600A5015
Instruction Manual
- 9 -
Setting on the operating part of the controls (onboard)
1
Input code number
3112
!
2
Press the
E
key
Parameter
5.0.0.
displayed
3
Press the
E
key
Sir
displayed. The 2 lower segments of the right 7 segment display flash.
4
Press the
>>
key
Parameter
2.9.0.
appears
(Functional cycle cutting
processes)
5
Press the
E
key
Parameter value e.g.
05
appears.
6
Press the
+/-
key
The parameter value can be changed.
7
Press the
E
key
Parameter
4.6.7.
appears
(Selection of motor)
8
Press the
E
key
Parameter value e.g.
3
appears.
9
Press the
+/-
key
The parameter value can be changed.
10
Press the
E
key
Parameter
1.1.1.
appears
(Maximum speed)
11
Press the
E
key
Value of the set speed appears.
12
Press the
+/-
key
The parameter value can be changed.
13
Press the
E
key
Parameter
1.6.1.
appears
(Direction of motor rotation)
14
Press the
E
key
Parameter value e.g.
1
appears.
15
Press the
+/-
key
The parameter value can be changed.
16
Press the
E
key
Parameter
2.7.0.
appears
(Type of position sensor)
17
Press the
E
key
Parameter value e.g.
0
appears.
18
Press the
+/-
key
The parameter value can be changed.
19
Press the
E
key
Parameter
2.7.2.
appears
(Transmission Ratio)
20
Press the
E
key
Parameter value e.g.
1000
appears.
21
Press the
+/-
key
The parameter value can be changed.
22
If parameter
270 =0 or 5
, or the check of the
transmission ratio is already done, continue with
Point 30.
23
Press the
E
key
PULY
is displayed.
(Check the transmission ratio)
24
Move pedal forwards
Let the drive run until ready (
rdy
) is displayed.
For a maximum speed that is too high, an error
message A12 is generated.
Push button
E
as
often as needed until parameter
111
(Point 12) is
reached again to set the permitted maximum
speed.
25
Press pedal to position 0
(neutral)
The check is complete.
26
When parameter
270 ≠ 6
, continue with Point
31.
27
P0 o
is displayed (
o
in red).
(Setting the reference position)
28
Rotate the hand wheel in the running direction until
o
extinguishes
*
.
Set reference position (e.g. height of the stitch plate, lower dead point).
29
Press the
E
key
Parameter
4.5.1.
appears
(Position 1 leading edge,
position 1 trailing edge is
automatically set 60° higher)
30
Press the
E
key
Angle from position 1 is displayed.
31
Turn the hand wheel
Set position 1 (at least 1 rotation
*
).
32
Or
press the
+/-
key
The parameter value can be changed.
33
Press the
E
key
Parameter
4.5.3.
appears
(Position 2 leading edge,
position 2 trailing edge is
automatically set 60° higher)
34
Press the
E
key
Angle from position 2 is displayed.
35
Turn the hand wheel
Set position 2 (at least 1 rotation
*
).
36
Or
press the
+/-
key
The parameter value can be changed.
37
Upon pressing the
E
key once more the program returns to parameter
2.9.0.
!
38
Press the
P
key twice
The system exits the SIR routine.
*) All operations carried out by turning the hand wheel must always be carried out in the direction of rotation set up on the
machine. Under no circumstances should you turn against the machine direction.
Содержание AB600A5015
