Efka AB600A5015 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 64

background image

- AB AB600A5015

Instruction Manual

- 15 -

6.3 Transmission Ratio

N

OTE

The transmission ratio must always be input if no transmission ratio of 1:1 exists, because only motors with
integrated incremental transmitters will be used.

The transmission ratio should be determined and set as

precisely as possible!

The transmission ratio between motor shaft and shaft of the sewing machine head must be input, so that the set
speeds of parameters

110...117

correspond to the sewing speeds.

Function

Parameters

Transmission ratio between motor shaft and machine shaft

(trr)

272

The transmission ratio can be selected within a range of 150...40000 using parameter

272

.

Example:

With a motor pulley diameter of 40 mm and a sewing machine head pulley diameter of
80

mm

the

value

500

can

be

calculated

using

the

formula

below.

If the value 2000 has been selected in parameter 272, it follows that the motor pulley is
double the size of the sewing machine head pulley.

Motor pulley diameter

Value of parameter

272

= -------------------------------------------------------------------- x 1000

Machine pulley diameter

6.4 Selection of Functional Sequences (Thread Trimming Operations)

This drive is suitable for different lockstitch, chainstitch and overlock machines. The mode for the functional
sequence required on the respective machine can be selected using parameter

290

.

A

TTENTION

Before switching the functional sequences, you must disconnect input and output plug-and-
socket connections between control and machine. Please ensure that the functional sequence
(mode) suitable for the respective machine is selected.

Settings with parameter 290 are possible only after the power is turned On.

You will find a summary of the modes that can be set and the corresponding machines and adapter cords, to
include available output signals in the List of Parameters chapter: Table of adapter cords.

Further information see chapter "Timing Diagrams" for the various modes.

The possible functions are listed in the section "Parameter list".

6.5 Key functions of the input in1

The function which is triggered by pressing a button or switch connected to input in1 can be selected with
parameter 240.
The possible functions are listed in the section "Parameter list"

6.6 Positioning speed

Function

with

or

without

control panel

Parameters

Positioning speed

(n1)

110

The positioning speed can be set using parameter

110

on the control within a range of 70...390 RPM.

«
...
13
14
15
16
17
...
»

Содержание AB600A5015

































































Отзывы:

Нет отзывов

Похожие инструкции для AB600A5015

Бренд: Manfrotto Страницы: 16

Бренд: Daikin Страницы: 5

Бренд: Danfoss Страницы: 32

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 44

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 144

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 64

Бренд: Danfoss Страницы: 8

VLT AutomationDrive FC 360

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 6

Бренд: Danfoss Страницы: 4

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 2

ECL Comfort 110

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 24

Бренд: Gardner Denver Страницы: 22

Бренд: B&G Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды