![background image](http://html1.mh-extra.com/html/efco/sparta-381/sparta-381_operators-instruction-book_2366954038.webp)
34
GB
NYLON LINE HEAD
Only use line of the same diameter as the original
to avoid overloading the engine (Fig. 18).
In order to get more line out of the cutting head,
tap it lightly on the ground while working.
Note:
Never hit the nylon head against hard spots
such as concrete or stones, it could be dangerous.
Replacing the nylon line on the LOAD&GO
trimmer head (Fig.19)
1. Cut 6.0 m of nylon line Ø 3.0 mm.
2. Align the arrows and insert the line into the
trimmer head (Fig. 19.1) until it is released from
the opposite side (Fig.19.2).
3. Divide the line into two equal parts (Fig. 19.3)
and then load the trimmer head by turning the
knob (Fig. 19.4).
WARNING! – Always wear protective
gloves during maintenance operations. Do not
carry out maintenance with the engine hot.
Never use fuel for cleaning operations.
AIR FILTER
Every 8-10 working hours, remove the cover (A,
Fig. 22), clean the filter (B).
Blow with compressed air, at a distance.
Replace if dirty or damaged. The engine runs
irregularly if the filter is clogged, with consequent
higher consumption and lower performance.
FUEL FILTER
Check fuel filter periodically. A dirty filter can cause
difficult starting and lower engine performance.
To clean filter proceed as follows: remove it from
fuel filling hole. Replace it (Fig. 21) if too dirty.
ENGINE
Clean cylinder fins with a brush or compressed
air periodically. Dangerous overheating of engine
may occur due to impurities on the cylinder.
SPARK PLUG
Clean spark plug and check electrode distance
periodically (Fig. 23). Use Champion NGK BPMR7A
or of other brand with the same thermal grade.
BLADE SHARPENING (2-3-4 TOOTH)
1. Blades are reversible: when one side is no
longer sharp, the blade can be turned over
and used on the other side (Fig. 17).
2. Blades are sharpened using a flat single-cut
file (Fig. 17).
3. To maintain the correct balance, file all cutting
edges uniformly.
4. If the blades are not sharpened correctly, this
can set up abnormal vibrations in the machine
and cause the blades themselves to break
ultimately.
BLADE SHARPENING (8 TOOTH)
Always check the general condition of the blade.
Correct sharpening permits the maximum
performance of the brush cutter. To sharpen the
teeth, use a file or grindstone and proceed with
light touches, respecting the corners and the
dimensions shown in Fig. 11.
SHARPENING THE SAW BLADE
• See the cutting attachment packaging for
correct sharpening instructions.
A correctly sharpened blade is essential for
working efficiently and to avoid unnecessary
wear to the blade and clearing saw.
• Make sure that the blade is well supported
when you file it. Use a 5.5 mm round file.
• The filing angle is 15°. File alternate teeth to
the right and those in between to the left. If
the blade has been heavily pitted by stones it
may be necessary to dress the top edges of
the teeth with a flat file, in exceptional cases. If
so, this should be done before filing with a
round file. The top edges must be filed down
by the same amount for all the teeth.
WARNING! –
The wrong type of cutter or
an incorrectly sharpened blade will increase the
risk of kickback. Check mower blades for
deterioration or cracks, and replace if damaged.
WARNING: Never repair damaged
cutting attachments by welding,
straightening or modifying the shape. This
may cause parts of the cutting tool to come
off and result in serious or fatal injuries.
Содержание SPARTA 381
