P/N 3100346 ISSUE 3
PAGE 3
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
During installation, care must be taken so that components
on the printed circuit board are not damaged.
1. Mount Adaptatone as shown in Figure 3.
a.
Flat Surface Mounting
. Secure unit to
mounting surface using the (4) mounting holes in
the mounting plate on the rear of the box. Use
the #10 x 3" (76 mm) wood screws (furnished loose)
or other hardware (not supplied) suitable for the
mounting surface.
b.
Rigid Pipe Mounting
. Loosen the (4) cover screws
from the signal box and lift off signal box cover.
NOTE:
Cover screws are captive. Do not remove from
cover.
Remove the center knockout in lower wall of box
and mount box to a 1/2" (12.7 mm) conduit pipe
using suitable connector.
2. Install wires through a knockout hole in the bottom
of the box from a raceway that is, with its connections
to the 1/2" (12.7 mm) conduit knockout hole, approved
for the same degree of protection and enclosure type
needed by the application. Use the provided plastic
tie-wrap, on the barrier to the electronics, to separate
incoming power leads from signal and tone initiating
leads, per NEC (Figures 4, 5 and 6).
Figure 3. Adaptatone Mounting
WARNING
WARNING
WARNING
WARNING
WARNING
To prevent fire and shock, wire the Adaptatone only as
described in this installation instruction.
d. Connect incoming power to wire leads using a
butt splice or other method listed, certified, or
otherwise approved by local authorities. Leads
are black and white.
e. Optional. Connect external 24V DC battery (not
supplied) in series with separate diode assembly
part 2600010 (supplied) to TB1 terminals 3 and 4
on the main board as shown in Figures 4 and 5
and marked on the diode assembly.
NOTE:
Terminal Block TB1 can be unplugged from the
main board to complete wiring as shown in
Figure 4.
4. Wire the 5532M series speaker/amplifier as follows
referring to Figures 6, 7 and 8:
a. Connect green and yellow striped earth-ground
wires to earth-ground.
b. See Figure 8. Connect audio output (+) from the
main board of the tone generator to the AUD (+)
terminal on the Speaker/Amplifier Audio Coupler
Board. Connect audio output (-) from the main
board of the tone generator to the AUD (-) terminal
on the Speaker/Amplifier Audio Coupler Board.
Use shielded cable and connect braid or drain to
earth-ground wire lead of 5540 Tone Generator.
c. Connect incoming power to wire leads using a
butt splice or other method listed, certified, or
otherwise approved by local authorities. Leads
are both black for -AQ and -N5 models and are
black for line and white for neutral for -Y6 models.
e. Optional. Connect external 24V DC battery (not
supplied) in series with separate diode assembly
part 2600010 (supplied) to TB1 terminals 3 and 4
on the main board as shown in Figure 7 and
marked on the diode assembly.
NOTE:
Terminal Block TB1 can be unplugged from the
main board to complete wiring as shown in
Figure 7.
5. Wire to the 5532B series speaker/amplifier as follows
and referring to Figures XX:
a. Connect green earth-ground wire of speaker/
amplifier and green and yellow striped earth-
ground wires on tone generator to earth-ground.
b. Connect audio output (+) from the main board of
the tone generator to the Tone In terminal 9 (+) in
the Speaker/Amplifier. Connect audio output (-)
from the main board of the tone generator to the
Tone In Termal 10 (-) in the Speaker/Amplifier.
d. For 5532B-AQ, 5532BDV2-AQ and 5532BHV-AQ
models, connect power source to the Speaker/
Amplifiers at TS2. Polarity must be observed for
DC models.
e. For 5532B-Y6, 5532BDV2-Y6, 5532BHV-Y6, and
5532B-N5 models, connect incoming power to wire
leads from power supply. For -Y6 models using a
DC source, black wire is positive and white is
negative and polarity must be observed. For AC
source, black is line and white is neutral.
g. Optional. Wire 24V DC battery backup to TS1-1
and TS1-2 of the Speaker/Amplifier per Figure 18
and connect 24V DC battery backup in series with
diode assembly part 2600010 (supplied) to TB1
3. Wire the 5540M Series Tone Generator referring to
Figures 4 and 5 as follows:
a. Connect green and yellow-striped earth-ground
wires to earth-ground.
b. Connect the RS485 wires to terTX/RX and
-TX/RX on the RS485 COMM board (Figure 5).
c. If using the optional MR201/C relay, connect the
relay to +RELAY and -RELAY on the RS485 COMM
board (Figure 5).
Speaker
Large star nut to
adjust speaker
direction
Signal Box
(4) Cover
screws
Signal Box
(4) Cover
screws
(4) Collar
gaskets
(4) Collar
gaskets
Raceway and connections
(not supplied)
to the 1/2" (12.7 mm)
knockout hole
(4) #10 x 3" (76 mm)
screws or other hardware
suitable for the mounting surface
