Edwards Signaling 5532M-AQ, Руководство по установке

Страница: 4 / 26

P/N 3100346 ISSUE 3 PAGE 4
W A R N I N G S W A R N I N G S
W A R N I N G S W A R N I N G S W A R N I N G S
Ensure that the (4) collar gaskets, part number P-041930-
0362, are in place on each cover screw before securing the
signal box cover.
When securing cover, start screws by hand, making sure
they are threaded into tapped holes in housing bosses
before securing with a screwdriver. Torque signal box cover
screws to a minimum of 20 in-lbs. This ensures the
required tight fit.
WARNING WARNING WARNING WARNING WARNING
To ensure integrity of the Adaptatone assembly when
adjusting the speaker direction, make sure threads in the
enclosure remain fully engaged and do not turn speaker
more than 360 degrees from the original factory installed
position.
WARNING WARNING
WARNING WARNING
WARNING
Ensure that power is disconnected before cleaning inside of
unit.
terminals 3 and 4 on the main board of the tone
generator per Figure 7. Polarities must be observed.
WARNINGS WARNINGS
WARNINGS WARNINGS
WARNINGS
HIGH VOLTAGE is present when product is energized. High
volume may cause harm to personnel in close proximity.
6. Adjust volume level, if desired, by turning
potentiometer located on the main board (Figures 13,
14, 15 and 18) and on voice board (Figure 2).
7. To adjust speaker direction, loosen large star nut
(Figure 3) and turn speaker to the approximate desired
position. Retighten nut and turn speaker slightly
clockwise until locked into place.
8. Tightly secure the signal box cover using (4) retained
cover screws.
9. Torque signal box cover screws to a minimum of 20
in-lbs.
10. Verify operability.
Maintenance and Maintenance and
Maintenance and Maintenance and
Maintenance and T T
T T
Test est
est est
est
Examine the unit semi-annually for accumulation of dirt.
Clean if necessary.
The Adaptatone should be tested annually or as required
by the authority having jurisdiction to ensure continuous
service.
WARNING WARNING WARNING WARNING WARNING
To ensure integrity of the enclosure: Ensure the cover
gasket, part number P-007549-0069, is adhered into
groove at cover perimeter before replacing the signal box
cover.
Protocol Protocol Protocol Protocol Protocol
1.0 Setting Unit Address and Network Baud Rate
1.1 Locate the 8-position dip switch, S1, on the top edge of the RS485 COMM board (Figure 6).
1.2 Unit address range is 00-1F hex. (00-31 decimal). Refer to Table 2.2 for unit address configuration. Set S1
positions 1-5 for the desired unit address configuration.
Table 2.2 Unit Address Switch Configuration
Unit Address S1-1 S1-2 S1-3 S1-4 S1-5
Hex Decimal
00 00 OPEN OPEN OPEN OPEN OPEN
01 01 CLOSED OPEN OPEN OPEN OPEN
02 02 OPEN CLOSED OPEN OPEN OPEN
03 03 CLOSED CLOSED OPEN OPEN OPEN
04 04 OPEN OPEN CLOSED OPEN OPEN
05 05 CLOSED OPEN CLOSED OPEN OPEN
06 06 OPEN CLOSED CLOSED OPEN OPEN
07 07 CLOSED CLOSED CLOSED OPEN OPEN
08 08 OPEN OPEN OPEN CLOSED OPEN
09 09 CLOSED OPEN OPEN CLOSED OPEN
0A 10 OPEN CLOSED OPEN CLOSED OPEN
0B 11 CLOSED CLOSED OPEN CLOSED OPEN
0C 12 OPEN OPEN CLOSED CLOSED OPEN
0D 13 CLOSED OPEN CLOSED CLOSED OPEN
0E 14 OPEN CLOSED CLOSED CLOSED OPEN
0F 15 CLOSED CLOSED CLOSED CLOSED OPEN