EDAN F15 Series Скачать руководство пользователя страница 7

Страница: 7 / 80

F15 Series Fetal & Maternal Monitor Service Manual Safety Guidance

Chapter 1 Safety Guidance

NOTE:

This service manual is written to cover the maximum configuration. Therefore, your

model may not have some of the parameters/modules described, depending on what you

have ordered.

1.1 Introduction

This service manual is a reference for periodic preventive maintenance and corrective service

procedures for the

F15

and

F15 Air

fetal & maternal monitor.

It provides troubleshooting information, assembly procedures, instructions for functional testing

and performance verification. It is intended for use only by technically qualified service

personnel.

WARNING

When performing a service procedure, follow the instructions exactly as presented in this

manual. Failure to do so might damage the monitor, invalidate the product warranty or

lead to serious personal injury.

1.2 General Information

NOTE:

In this manual,

Monitor

refers to both

F15

and

F15 air

, and is used where the information

applies to both models.



The monitor is designed to comply with the international safety requirements IEC/EN

60601-1 for medical electrical equipment. It is class I equipment.



The monitor operates within specifications at ambient temperatures between 0º

C (+41 º

and +40 º

C (+104 º

F). Ambient temperatures that exceed these limits could affect the

accuracy of the instrument and cause damage to the modules and circuits. Allow at least 2

inches (5 cm) clearance around the instrument for proper air circulation.



You must check that the equipment, cables and transducers do not have visible evidence of

damage that may affect patient safety or monitoring capability before each use. If damage is

evident, replacement is recommended before use.



The monitor must be serviced only by authorized and qualified personnel. The manufacturer

Содержание F15 Series

















































































Результаты поиска

Содержание F15 Series

Отзывы:

Бренды по названию

Популярные бренды

EDAN F15 Series, Руководство по обслуживанию

Результаты поиска

Содержание F15 Series

Отзывы:

Бренды по названию

Популярные бренды