manualshive.com logo in svg

EDAN F15 Series, Руководство по обслуживанию

Поделиться
Скачать
EDAN F15 Series Скачать руководство пользователя страница 22

F15 Series Fetal & Maternal Monitor Service Manual                                                    Functional Checks 

- 11 - 

3.4 Printing Check 

Press the 

PRINT

 key to start printing. Check if the recorder starts printing. 

Enable  the 

Print  Self-Test

  function.  Restart  the  monitor  and  verify  if  the  recorder  prints  a 

baseline. 

Enter 

DEMO

 mode and print some traces and check if all the traces are clear on the paper. 

If any failure is detected, refer to section 

7.5 Recorder Failures

 for details. 

NOTE:   

Please make sure the paper loading and setting are correct before the printing starts.

 

3.5 Alarms Check 

Stimulate a signal  that is higher than the upper limit  or lower than the lower limit  to  activate  a 

physical alarm. Disconnect one of the plugs off the monitor to activate a technical alarm. Check if 

the audible alarms and visible alarms are working properly. 

If any failure is detected, refer to section 

7.7 Alarm Failures

 for defective details.   

Содержание F15 Series

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды