Eclipse ETEK 5 Скачать руководство пользователя страница 28

Страница: 28 / 80

ADVANCED SET-UP

28 ETEK5 MANUAL

DWELL

The Dwell parameter controls the amount of time that the

solenoid valve is energised and therefore the amount of gas

that is released with each shot.
The Dwell parameter is indicated by a purple light on the

navigation console when you are in the set-up mode.
This parameter is adjustable between 8.0ms and 16.0ms in

0.1ms increments.

DEBOUNCE

The Debounce parameter is used to set the level of

Debounce (anti-trigger bounce) on the ETEK5.

The Debounce parameter is indicated by a light blue LED on

the navigation console when you are in the set-up mode.
This parameter is adjustable between 1 and 10 with a higher

value reducing the amount of trigger bounce.

THE FACTORY RESET

Whilst in set-up mode, it is possible to reset all of the control

parameters to the factory default settings in the following

way:

Push and hold the tournament lock button (see page

24 for information on the tournament lock button) for two

seconds.

The LED on the navigation console will repeatedly flash

blue to indicate that the factory default settings have

been restored.

The ETEK5 software parameters and presets are correct at time of printing. However newer

versions of the ETEK5 software may have different parameters and presets to those printed above.

Some parameters may have ben added or removed entirely. Please contact your nearest service

centre if you have any queries regarding the ETEK5 software installed in your marker.

Содержание ETEK 5

















































































Результаты поиска

Содержание ETEK 5

Отзывы:

Похожие инструкции для ETEK 5

Бренды по названию

Популярные бренды

Eclipse ETEK 5, Руководство пользователя

Результаты поиска

Содержание ETEK 5

Отзывы:

Похожие инструкции для ETEK 5

Бренды по названию

Популярные бренды