Eclipse ETEK 5 Скачать руководство пользователя страница 25

Страница: 25 / 80

USING THE ETEK5

ETEK5 MANUAL 25

UNDERSTANDING THE BREECH SENSOR OPERATION

The ETEK5 displays the status of the Breech Sensor using the LED on the

navigation console as follows:

INDICATION

BREECH SENSOR STATUS

Flashing yellow

BS enabled. No paintball detected

- Marker will not fire

Flashing light blue

BS enabled. Paintball detected

- Marker will fire

Flashing purple (slow)

disabled - Marker will fire

Flashing purple (fast)

Blockage detected - BS temporarily

disabled - Marker will fire

Any changes to the Breech Sensor status will be displayed immediately.

This provides valuable feedback to the user.
The BS is able to switch itself off in the event that a blockage or contamination

prevents it from functioning correctly. This is represented by a fast flashing

purple LED on the navigation console. The ETEK5’s ROF will be capped at

2bps less than the Maximum ROF with BS Off up to a maximum of 10bps. In this

instance, the BS will switch itself back on once the blockage is cleared and the

correct operation of the BS can then be resumed.

THE BATTERY LEVEL INDICATOR

When the ETEK5 is turned on, the level of the battery will be displayed on the

LED (after an initial blue flash

signifying the ETEK5 has powered on).

The status of the battery can be displayed manually on the LED by quickly

pressing and releasing

on the navigation console.

When the battery is fresh the LED will flash green. As the battery is drained the

LED will change colour from green to yellow then red.
When the battery reaches a level where it will no longer function reliably, the LED

will start to flash red. At this point the battery must be changed for a new one.

For instructions on installing a new battery see page 7.

1 The colour of this flash may vary depending on the region the marker has originally been

purchased.

WARNING!

When the battery level indicator is being displayed the marker is still on and

will fire if the trigger is pulled (dependant on the condition of the BS).

WARNING

Содержание ETEK 5

















































































Результаты поиска

Содержание ETEK 5

Отзывы:

Похожие инструкции для ETEK 5

Бренды по названию

Популярные бренды

Eclipse ETEK 5, Руководство пользователя

Результаты поиска

Содержание ETEK 5

Отзывы:

Похожие инструкции для ETEK 5

Бренды по названию

Популярные бренды