Eclipse ETEK 5 Скачать руководство пользователя страница 18

Страница: 18 / 80

USING THE ETEK5

18 ETEK5 MANUAL

INSTALLING A PRESET AIR SYSTEM (CONTINUED)

High, mid and low pressure output preset air systems can be used with the

ETEK5, providing the ETEK5 is fitted with the SL4 inline regulator originally

supplied with the marker.

There are two retaining screws on the On/Off Purge System (OOPS) body

underside

(see figure 12A)

. These are used to clamp the OOPS onto the frame.

It is advisable to make sure that these screws are tight using a 5/32” hex key

before attaching an air system.
The Eclipse ETEK5 comes complete with an Eclipse On/Off Purge System

(OOPS) which provides a direct connection for a preset air system. Before

screwing an air system into the OOPS ensure that the OOPS knob is fully

unscrewed

(see figure 12B)

. In this position the OOPS is off and will not

pressurise the ETEK5 when an air system is screwed into the OOPS.
Lining the threads up correctly between the OOPS and the air system, screw the

air system into the OOPS until the air system is screwed all the way in and tight

on the OOPS. The air system MUST be screwed all the way in before turning on

the OOPS

(see figure 12C)

Now with the air system attached and the barrel pointing away from you, start

to slowly turn the OOPS knob counter-clockwise to turn the OOPS on and

pressurise the ETEK5. Keep turning the knob until it stops against the OOPS

body as shown in

figure 12D

You have now installed a preset air system onto your ETEK5.

FIG 12D

FIG 12C

FIG 12A

FIG 12B

Содержание ETEK 5

















































































Результаты поиска

Содержание ETEK 5

Отзывы:

Похожие инструкции для ETEK 5

Бренды по названию

Популярные бренды

Eclipse ETEK 5, Руководство пользователя

Результаты поиска

Содержание ETEK 5

Отзывы:

Похожие инструкции для ETEK 5

Бренды по названию

Популярные бренды