Eclipse ETEK 5 Скачать руководство пользователя страница 30

Страница: 30 / 80

ETEK5 OLED BOARD

30 ETEK5 MANUAL

ETEK5 OLED BOARD NAVIGATION CONSOLE

The optional ETEK5 OLED Board provides an enhanced interface which

gives the user more detailed information about the state of the ETEK5 and

provides a quicker and more visual way of altering your marker settings.

The OLED display

is used to:

•

Convey information and marker settings to the user.

The LED

is used to:

•

Provide Breech Sensor status.

•

Serve as a high visibility reminder that the ETEK5 is switched on.

The select button

is used to:

•

Switch the ETEK5 on and off.

•

Switch the Breech Sensor on and off.

•

Select a parameter for editing.

•

End parameter editing.

•

Exit set-up mode.

The trigger (not shown) is used to:

•

Enter set-up mode.

•

Cycle through the control parameters.

•

Adjust the control parameters.

FIG 19A

WARNING!

De-gas your marker,

discharging any stored

gas in a safe direction, and

remove the barrel, loader, air

system and any paintballs

before adjusting.

WARNING

Содержание ETEK 5

















































































Результаты поиска

Содержание ETEK 5

Отзывы:

Похожие инструкции для ETEK 5

Бренды по названию

Популярные бренды

Eclipse ETEK 5, Руководство пользователя

Результаты поиска

Содержание ETEK 5

Отзывы:

Похожие инструкции для ETEK 5

Бренды по названию

Популярные бренды