Eclipse ETEK 5 Скачать руководство пользователя страница 17

Страница: 17 / 80

USING THE ETEK5

ETEK5 MANUAL 17

WARNING!

Make sure the marker is turned off with a barrel blocking device installed

and that no paintballs are in the ETEK5 or loader before installing an air

system.
Compressed air and nitrogen systems can be extremely dangerous if

handled or used incorrectly.

Only use an air system certified for use within the country of use.

The ETEK5 cannot be used with CO2. Only use compressed air or nitrogen.

Never add any lubricants or greases into the fill adaptor of the air system

regulator.
Ensure that all screws are tightened and no parts are loose before installing

an air system.
Do not pressurise the ETEK5 without the bolt system correctly installed, as

high pressure gas will be emitted.
Do not install a compressed air system or load paintballs into the ETEK5

until you feel completely confident with your ability to handle the marker

safely and responsibly.
Always relieve all residual gas pressure from the ETEK5 before unscrewing

the preset air system.

WARNING

INSTALLING A PRESET AIR SYSTEM

Содержание ETEK 5

















































































Результаты поиска

Содержание ETEK 5

Отзывы:

Похожие инструкции для ETEK 5

Бренды по названию

Популярные бренды

Eclipse ETEK 5, Руководство пользователя

Результаты поиска

Содержание ETEK 5

Отзывы:

Похожие инструкции для ETEK 5

Бренды по названию

Популярные бренды