ECD TC80, Инструкция по эксплуатации, Страница: 47 / 53

46
SlaveExceptionError total count of exceptions detected 1
16 bit
Integer
R 5 05
SlaveMessage
total messages addressed to the slave (remote
device)
1
16 bit
Integer
R 6 06
SlaveNoResponse
total count of messages not responded to by the
slave (remote device)
1
16 bit
Integer
R 7 07
SlaveNAK
total Negative Acknowledges returned by slave
(remote device)
1
16 bit
Integer
R 8 08
SlaveBusy
total count of "slave busy" was returned for an
address message
1
16 bit
Integer
R 9 09
BusCharacterOverrun
count of messages that couldn't be handled due to
character over-run condition
1
16 bit
Integer
R 10 0A
Reset all Modbus Error
Counters
Resets all of the Modbus Error counters (defined in
Modbus spec) to 0, Write any value.
1
16 bit
Integer
W 11 0B
Product T80 Model Number
(Modbus)
The Model Number of the Unit polled 1
16 bit
Integer
R 12 0C
T80 Serial Number (hi word)
Unit Serial Number (32 bit integer hi word, bytes 3
and 2)
2
32 bit
Long
Integer
R
13 0D
T80 Serial Number (lo word)
Unit Serial Number (32 bit integer lo word, bytes 1
and 0)
14 0E
T80 Mode
Unit operating mode (1-Startup, 2-Sensor Search, 3-
Operate)
1
16 bit
Integer
R 15 0F
T80 Fault Status Unit Fault flags, bit defined 1
16 bit
Integer
R 16 10
T80 2nd Fault Status
Unit Fault flags (2nd word reserved, currently not
used)
1
16 bit
Integer
R 17 11
T80 Warning Status Unit Warning flags, bit defined 1
16 bit
Integer
R 18 12
T80 2nd Warning Status
Unit Warning flags (2nd word reserved, currently not
used)
1
16 bit
Integer
R 19 13
T80 FW Rev Firmware revision of the Control BD in ASC, ex. " 1". 1
16 bit
Integer
R 20 14
Relay Number to read/write
Relay number to access data (0 - Relay 1, 1 - Relay 2,
2 - Relay 3)
1
16 bit
Integer
RW 21 15
Relay Type
Read/Write Relay Type (0 - Fault Type, 1 - Alarm
Type, 2 - Disabled, 3 - Timed)
1
16 bit
Integer
RW Y 22 16
Relay ON Setpoint (hi word) Read/Write Relay ON Setpoint (byte 3 and byte 2)
2
32 bit
Floating
Point
RW Y
23 17
Relay ON Setpoint (lo word) Read/Write Relay ON Setpoint (byte 1 and byte 0) 24 18
Relay OFF Setpoint (hi
word)
Read/Write Relay OFF Setpoint (byte 3 and byte 2)
2
32 bit
Floating
Point
RW Y
25 19
Relay OFF Setpoint (lo
word)
Read/Write Relay OFF Setpoint (byte 1 and byte 0) 26 1A
Relay ON Delay (hi word)
Read/Write Relay turn on Delay time (byte 3 and
byte 2)
2
32 bit
Floating
Point
RW Y
27 1B
Relay ON Delay (lo word)
Read/Write Relay turn on Delay time (byte 1 and
byte 0)
28 1C
Relay OFF Delay (hi word)
Read/Write Relay turn off Delay time (byte 3 and
byte 2)
2
32 bit
Floating
Point
RW Y
29 1D
Relay OFF Delay (lo word)
Read/Write Relay turn off Delay time (byte 1 and
byte 0)
30 1E
Relay Energized State Read/Write Relay 0 - Energized, 1 - De-Energized 1
16 bit
Integer
RW Y 31 1F
Relay Expiration
Read/Write Expiration Time, used with alarm type (0
- None, 2 - 5min., 3 - 10min., 4 - 15min., 6 - 30min.)
1
16 bit
Integer
RW Y 32 20
Relay Period
Read/Write Timed Relay Period (0 - 15min., 1 -
30min., 2 - 1hr., 3 - 2hr., 4 - 4hr., 5 - 8hr., 6 - 24hr.)
1
16 bit
Integer
RW Y 33 21
Relay Duration
Read/Write Timed Relay Duration (0 - 15sec., 1 -
30sec., 2 - 1min., 3 - 2min., 4 - 5min., 5 - 15min., 6 -
10min.) 1
16 bit
Integer
RW Y 34 22