EBS Active Track Basic+ Скачать руководство пользователя

Страница: 7 / 55

FOR YOUR OWN SAFETY

Study the advice below carefully. Disregarding may be dangerous or illegal.

More information is provided in following parts of this Manual.

RADIO INTERFERENCE

The device is sensitive to radio interference that can influence quality of

connection.

DO NOT USE THE DEVICE WITHIN HOSPITAL AREA

Follow rules and regulations. Do not switch on the device where near to

medical equipment.

DO NOT USE THE DEVICE WHILE FILLING UP A CAR

Do not use the device either at petrol stations or petrol and chemical

depots.

SWITCH OFF THE DEVICE IN EXPLOSION AREA

Do not use the device where explosives are blasted off. Pay attention to
all limits and follow rules and regulations.

USE PROFESSIONALS

Get qualified service install and repair the device or its parts.

BATTERIES AND ACCESSORIES

Use batteries and accessories approved by The Manufacturer only. Do
not connect chargers not compatible with the device.

WATER AND DUST RESISTANCE

The device is dustproof and waterproof according. It is yet
recommended to keep it safe from excessive dust and humidity..

Содержание Active Track Basic+
























































Результаты поиска

Содержание Active Track Basic+

Отзывы:

Похожие инструкции для Active Track Basic+

Бренды по названию

Популярные бренды

EBS Active Track Basic+, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Active Track Basic+

Отзывы:

Похожие инструкции для Active Track Basic+

Бренды по названию

Популярные бренды