EBS Active Track Basic+ Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 55

background image

49

10.7.

Battery charging

Once in charger, the device starts charging automatically. It is being signalled

with flashing of “Call me” button.

Note:

When connected device had completely empty battery blue LED may become

darker for about 15 minutes.

If you select "Turn off LEDs when device connected to the charger "in

Advanced" tab (in the option "Device parameters"), the LEDs will be turned off during
battery charging. See chapter Advanced. After removing the device from the charger,

the LEDs will indicate the status of the device again.

If the option "Generate audible signal on server lost" is selected, the device

during battery charging will inform about the loss of connection to the server by using

a special audio signal - 9 short beeps. The signal will also appear when docking the
device in the charging cradle and the device is not connected to the server. See
chapter Advanced.

10.8.

Battery full

When battery is fully charged “Call me” button lights up.

Battery full

10.9.

System general error

When error is detected, it is being signalled with alternate flashing of “Panic”

and “Checkpoint” buttons. Contact your service immediately.

Note:

Similar signaling may be visible after powering-up device. It may last for 3

minutes and it does not mean failure.

«
...
47
48
49
50
51
...
»

Содержание Active Track Basic+
























































Отзывы:

Нет отзывов

Похожие инструкции для Active Track Basic+

Бренд: Garmin Страницы: 22

SporTrak SporTrak Color

Бренд: Magellan Страницы: 48

Бренд: Garmin Страницы: 76

Бренд: Navigon Страницы: 125

Бренд: Navibe Страницы: 8

Бренд: Geonav Страницы: 85

Бренд: Garmin Страницы: 88

Бренд: Topten Страницы: 17

Бренд: Topshine Страницы: 34

Бренд: Topcon Страницы: 108

Бренд: Konlen Страницы: 17

Бренд: Loc8r Страницы: 6

Бренд: Gosafe Страницы: 26

Бренд: NorthStar Страницы: 70

Бренд: NorthStar Страницы: 87

TimeSource 3000

Бренд: Symmetricom Страницы: 238

Бренд: Mictrack Страницы: 10

Бренд: S&T Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды