background image

18

EATON

  

Duraforce HMR Conversion Procedures Manual  E-MOPI-TM005-E   July 2012

Rear-Ported

HMR

Side-Ported

HMR

Minimum
Displacement
Adjustment

Adjustment
Stud (Typical)

Seal Nut 
(Typical)

Minimum
Displacement
Adjustment

Minimum Displacement  

Adjustment Procedure

Set Up and Procedure

Procedure for Adjusting the HMR Minimum 

Displacement

 Note

  

To properly adjust the minimum displacement of the HMR 

motor, it is preferable that the motor free-spin while making 

the adjustment - This would insure that the motor was at 

minimum displacement.If this is not possible, then the HMR 

must be completely unloaded when making the minimum 

displacement adjustment to insure that it is at minimum 

displacement.

 

 Start the prime mover and adjust it to operating 

speed.

 

 Actuate the HMR motor under no load to insure it is 

at minimum displacement.

Note

The HMR motor automatically defaults to minimum 

displacement unless:
•  The motor is loaded beyond the regulation begin setting in 

which case the motor automatically shifts to a displacement 

to accommodate the torque requirement.

•  Control pressure is supplied into the displacement override 

port thus forcing the HMR to maximum displacement.

 

To Adjust the Motor Minimum Displacement:

 

a.  Hold the adjustment stud stationary with the 6mm 

Allen Wrench.

 

b.  Loosen the seal nut with the 19mm wrench.

 

c.  Turn the adjustment stud IN to increase the 

minimum displacement or turn it OUT to decrease 

the minimum displacement.

 

d.  Once the desired minimum displacement has been 

acquired, hold the adjustment stud stationary with 

the 6mm Allen wrench and tighten the seal nut 

with the 19mm wrench. The proper torque for the 

seal nut is 60 N-m (44 ft-lb). 

 

Note

 

The following table illustrates 
the recommended minimum 
displacements and allowable 
rotational speeds for both Max. 
and Min. displacement. The 
HMR motors should NOT be 
operated at higher speeds if the 
recommended displacements 
are used, unless specifically 
approved by Eaton Engineering. 
If higher rotational speeds are 
required for your application, you 
must consult Eaton Engineering 
for the required minimum 
displacement setting.

1

2

3

  Size 

 

55 

75 

105 

135 

165

  Max Displacement 

18.3   25.3   35.0  

45.2   55.2 

  Limit (CC)
 

Continuous Max Speed at Max 

  Speed 

Displacement 

4100  3800  3500 

3200  3100

  (RPM) 

Continuous Max Speed at Min

 

Displacement 

4700 4400 4100  3700 3500

Содержание DuraForce HMR Series

























Отзывы: