background image

It is of vital importance, before attempting to 
operate your engine, to read the general 
'SAFETY INSTRUCTIONS AND WARNINGS' 
section on pages 2-5 of this booklet and to strictly 
adhere to the advice contained therein.

Also, please study the entire contents of this 
instruction manual, so as to familiarize yourself 
with the controls and other features of the 
engine.

Keep these instructions in a safe place so that 
you may readily refer to them whenever 
necessary.

It is suggested that any instructions supplied 
with the vehicle, radio control equipment, etc., 
are accessible for checking at the same time.

1

CONTENTS

SAFETY INSTRUCTIONS AND 

WARNINGS ABOUT YOUR O.S. ENGINE

ENGINE CONSTRUCTION, NOTES WHEN

APPLYING AN ELECTRIC STARTER

INSTRUCTIONS,

TOOLS, ACCESSORIES, etc.

BASIC ENGINE PARTS,

CARBURETOR CONTROLS  (11J)

INSTALLATION

NOTES CONCERNING THE RECOIL STARTER

GLOWPLUG

STARTING THE ENGINE &

RUNNING-IN ('Breaking-in)

2-5

6-7

8-10

12-14

15

36

FINAL ADJUSTMENT

CARBURETOR CLEANLINESS,

CARE AND MAINTENANCE

CHECKING THE ENGINE,

TROUBLE SHOOTING

EXPLODED ENGINES  VIEWS &

PARTS LIST

CARBURETOR EXPLODED VIEW  & 

PARTS LIST

O.S. GENUINE PARTS & ACCESSORIES

THREE VIEW DRAWING

30-33

11-12

16-20

34-35

21-22

23-25

25-29

37-38

Summary of Contents for MAX-18CV-RM





















Reviews: