background image

To order parts and supplies: 800.343.9353  >>  eastwood.com 

5

GENERAL SAFETY RULES

Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “electrical equipment” in all of 
the warnings listed below refers to your mains-operated (corded) electrical equipment or battery-operated (cordless) electrical equipment.

SAVE THESE INSTRUCTIONS

1)  WORK AREA SAFETY

a)

  Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b)

  Do not operate electrical equipment in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Electrical equipment creates 

sparks which may ignite the dust or fumes.

c)

  Keep children and bystanders away while operating electrical equipment. Distractions can cause you to lose control.

2)  ELECTRICAL SAFETY

a)

  Electrical equipment plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) electrical 

equipment. Unmodified plugs and matching outlets will reduce risk of electric shock.

b)

  Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if 

your body is earthed or grounded.

c)

  Do not expose electrical equipment to rain or wet conditions. Water entering electrical equipment will increase the risk of electric shock.

d)

  Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the electrical equipment. Keep cord away from heat, oil, sharp edges or  

moving parts. Damaged or entangled cords increase the risk of electric shock.

e)

  When operating electrical equipment outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk  

of electric shock.

3)  PERSONAL SAFETY

a)

  Stay alert, watch what you are doing and use common sense when operating electrical equipment. Do not use electrical equipment while you are tired or 

under the influence of drugs, alcohol or medication. A moment of inattention while operating electrical equipment may result in serious personal injury.

b)

  Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used  

for appropriate conditions will reduce personal injuries.

c)

  Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying electrical equipment with your finger on the switch or  

plugging in electrical equipment that have the switch on invites accidents.

d)

  Remove any adjusting key or wrench before turning the electrical equipment on. A wrench or a key left attached to a rotating part of the electrical  

equipment may result in personal injury.

e)

  Do not overreach. Keep proper footing and balance at all times. This enables better control of the electrical equipment in unexpected situations.

f)

  Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair  

can be caught in moving parts.

g)

  If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these devices 

can reduce dust-related hazards.

Содержание 32498





















Отзывы: