6
7
Flying Checklist
Please note this checklist is not intended to be a replacement for the content included in this instruction manual .
Although it can be used as a quick start guide, we strongly suggest reading through this manual completely before
proceeding .
q
Always turn the transmitter on first
q
Plug the flight battery into the 2-in-1 control unit
q
Allow the 2-in-1 control unit and gyro to arm and initialize properly
q
Fly the model
q
Land the model
q
Unplug the flight battery from the 2-in-1 control unit
q
Always turn the transmitter off last
Battery Warnings, Guidelines and Charging
While the 11.1V 800mAh 3-cell Lithium Polymer Battery Pack (EFLB0995) included with your Blade
CP Pro 2 features Charge Protection Circuitry and Balance Charging via the included 3-cell Lithium
Polymer Balance Charger (EFLC3105), to help ensure a safe charge every time, you MUST read the
following safety instructions and warnings before handling, charging or using the LiPo battery pack.
Note: Lithium Polymer batteries are significantly more volatile than the alkaline, NiCd or
NiMH batteries used in RC applications. All instructions and warnings must be followed
exactly. Mishandling of LiPo batteries can result in fire.
By handling, charging or using the included LiPo battery you assume all risks associated with lithium
batteries. If you do not agree with these conditions, return your complete Blade CP Pro 2 model in
new, unused condition to the place of purchase immediately.
• You must charge the included 11.1V 800mAh 3-cell LiPo battery pack in a safe area away from
flammable materials .
• Do not charge the battery when installed in the helicopter.
• Never charge the battery unattended. When charging the battery you should always remain in constant
observation to monitor the charging process and react to potential problems that may occur .
• After flight, the battery must be cooled to ambient temperature before charging.
• You MUST use the included 3-cell 11.1V LiPo Balance Charger ONLY. Failure to do so may result in a fire
causing personal injury and/or property damage . DO NOT use a NiCd or NiMH charger.
• If at any time during the charge or discharge process the battery begins to balloon or swell, discontinue charging
or discharging immediately . Quickly and safely disconnect the battery, then place it in a safe, open area away
from flammable materials to observe it for at least 15 minutes . Continuing to charge or discharge a battery that
has begun to balloon or swell can result in a fire . A battery that has ballooned or swollen even a small amount
must be removed from service completely .
• In the event of a crash, you must quickly and safely disconnect and remove the battery from the model, then
place it in a safe, open area away from flammable materials to observe it for at least 15 minutes .
• Store the battery at room temperature for best results.
• When transporting or temporarily storing the battery, the temperature range should be from 40–120 degrees
Fahrenheit . Do not store the battery or model in a car or direct sunlight whenever possible . If stored in a hot
car, the battery can be damaged or even cause a fire .
• Do not over-discharge the battery. Discharging the battery too low can cause damage to the pack
resulting in reduced performance and duration.
LiPo cells should not be discharged to below 3V each under load. In the case of the 3-cell
LiPo packs used for the Blade CP Pro 2, you will not want to allow the battery to fall to below
9 volts during flight.
The Blade CP Pro 2’s 3-in-1 control unit does not feature a voltage cutoff of any type, so we
suggest that you be extremely aware of the power level of the LiPo battery pack. If at any time
the helicopter begins to require more throttle than typical to maintain hover or flight, or has lost
significant power, you must land the helicopter and power the motors down IMMEDIATELY to prevent
over-discharge of the LiPo battery pack. If you continue to run the motors after noticing a loss in
power, it is possible to discharge the LiPo battery pack too far, causing permanent damage to the
pack. Over-discharge of the LiPo battery pack can result in shortened flight times, loss of power
output or failure of the pack entirely.
If you have any further questions or concerns regarding the handling, charging and/or use of the included LiPo
battery pack, please contact the Horizon Support Team at 1 .877 .504 .0233 .
Содержание Blade CP Pro 2
Страница 40: ...78 79 ...