E-FLITE Blade 400 3D Скачать руководство пользователя

Страница: 5 / 25

Preparing for the First Flight Checklist

Please note this checklist is not intended to be a replacement for the content included in this instruction

manual. Although it can be used as a quick start guide, we strongly suggest reading through this

manual completely before proceeding.

Remove and inspect contents

Begin charging the flight battery

Install the 4 included AA batteries in the transmitter

Install the flight battery in the helicopter (once it has been fully charged)

Test the controls

Familiarize yourself with the controls

Find a suitable area for flying

Flying Checklist

Please note this checklist is not intended to be a replacement for the content included in this instruction

manual. Although it can be used as a quick start guide, we strongly suggest reading through this

manual completely before proceeding.

Always turn the transmitter on first

Plug the flight battery into the electronic speed control (ESC)

Allow the ESC and gyro to arm and initialize properly

Fly the model

Land the model

Unplug the flight battery from the ESC

Always turn the transmitter off last

Battery Warnings and Guidelines

While the 3S 11.1V 1800mAh Lithium Polymer Battery (EFLB18003S) included with your Blade 400

3D features Charge Protection Circuitry and Balance Charging via the included 3S 11.1V 1.8-Amp

Lithium Polymer Balancing Charger (EFLC3115) to help ensure a safe charge every time, you MUST

read the following safety instructions and warnings before handling, charging or using the Li-Po

battery.

Note: Lithium Polymer batteries are significantly more volatile than the alkaline, Ni-Cd or

Ni-MH batteries used in RC applications. All instructions and warnings must be followed

exactly. Mishandling of Li-Po batteries can result in fire.

By handling, charging or using the included Li-Po battery you assume all risks associated with

lithium batteries. If you do not agree with these conditions, return your complete Blade 400 3D

model in new, unused condition to the place of purchase immediately.

• You must charge the included 3S 11.1V 1800mAh Li-Po battery in a safe area away from

flammable materials.

• Do not charge the battery when installed in the helicopter.
• Never charge the battery unattended. When charging the battery you should always remain in

constant observation to monitor the charging process and react to potential problems that may

occur.

• After flight, the battery must be cooled to ambient temperature before charging.

• You MUST use the included 3S 11.1V 1.8-Amp Li-Po Balancing Charger ONLY. Failure to do so

may result in a fire causing personal injury and/or property damage. DO NOT use a Ni-Cd or

Ni-MH charger.

• If at any time during the charge or discharge process the battery begins to balloon or swell,

discontinue charging or discharging immediately. Quickly and safely disconnect the battery,

then place it in a safe, open area away from flammable materials to observe it for at least 15

minutes. Continuing to charge or discharge a battery that has begun to balloon or swell can

result in a fire. A battery that has ballooned or swollen even a small amount must be removed

from service completely.

Содержание Blade 400 3D


























Результаты поиска

Содержание Blade 400 3D

Отзывы:

Похожие инструкции для Blade 400 3D

Бренды по названию

Популярные бренды

E-FLITE Blade 400 3D, Руководство пользователя

Результаты поиска

Содержание Blade 400 3D

Отзывы:

Похожие инструкции для Blade 400 3D

Бренды по названию

Популярные бренды