E.F. Johnson Company 5300 ES Series Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 142

background image

3-2

5300 ES Series Mobile Radio Operating Manual

General Operation

• Last Zone/Home Channel

• Home Zone/Last Channel

• Home Zone/Home Channel

The Home Zone and Channel are pre programmed. With the “Last Zone”/“Home
Channel” configuration, the programmed home channel number of the last active zone is
selected. If this channel number is not programmed in the active zone, “UNPROGRAMD”
is displayed.

If the Radio ID feature is enabled, the radio will display the Radio ID alias in place of the
Self Test message during startup. Radio ID identifies the personality file used to program
the radio, the service area for which the radio is programmed, or functional grouping for
which the radio is programmed. The Radio ID alias display will be included with the
Radio Info display items in both button/scroll and menu modes. If disabled, the Radio ID
menu mode will display a blank line.

Note

In dual control configurations (front mount radio with remote control unit), the power
switch at either control point can be OFF for power to turn OFF.

3.1.1

Setting Volume Level

The relative volume setting can be determined using a reference tone as follows:

• If the key press tones are enabled (see Section 4.6), a short tone sounds when an option

switch is pressed or the Select switch is pressed or rotated.

• If a conventional channel is selected, take the microphone off-hook and if someone is

talking, voice may be heard. If the MON (Monitor) option switch is programmed (see
Section 5.3 on page 25), pressing it unsquelches the radio and either voice or
background noise is heard. If a SMARTNET/SmartZone or P25 trunked channel is
selected, the radio cannot be manually unsquelched.

The minimum volume level that the volume control can select can be programmed. This
can be used to prevent missed messages caused by unintentionally turning the volume
down too far. Relative levels of 0-255 can be set in steps of 1 (“0” sets the lowest
minimum volume).

Note

This setting is applicable to ES mobiles with ES Series Remote Control Heads. The
minimum volume setting has no effect on the volume of a pre-ES Series model remote
control head using an internal speaker whether it is attached to a pre-ES Series or an ES
Series mobile radio.

«
...
26
27
28
29
30
...
»

Содержание 5300 ES Series















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5300 ES Series

TALON UDC SERIES

Бренд: Kantronics Страницы: 101

Бренд: Sangean Страницы: 71

Бренд: Ubiquiti Страницы: 33

Бренд: Blaupunkt Страницы: 56

Бренд: RJE Страницы: 13

Бренд: CUSHCRAFT Страницы: 12

Бренд: auna Страницы: 76

Бренд: Telefunken Страницы: 18

freecomm 150 PMR 446

Бренд: stabo Страницы: 20

NS-HD01 - Portable HD Radio

Бренд: Insignia Страницы: 2

GEONAUTE On channel 700

Бренд: OXYLANE Страницы: 244

Бренд: Exibel Страницы: 12

Бренд: Hyundai Страницы: 28

1000 Smart Cart

Бренд: Noggin Страницы: 119

Бренд: Sharper Image Страницы: 11

Бренд: nanoradar Страницы: 16

Бренд: HYT Страницы: 19

Бренд: HYT Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды