E.F. Johnson Company 5300 ES Series Скачать руководство пользователя страница 102

Страница: 102 / 142

7-2

5300 ES Series Mobile Radio Operating Manual

March 2008

• Dynamic regrouping has been exited but the dynamic regrouping channel is still

selected (Section 6.12).

Single Short Medium-Pitch Tone

• A valid key has been pressed.

Single Short Low-Pitch Tone

• An invalid key has been pressed.

Medium Tone (No Acknowledge)

• The paged radio did not acknowledge the page (Section 6.6).

• The message that was sent has not been acknowledged (Section 6.7).

• The status condition that was sent has not been acknowledged (Section 6.8).

Five Beeps (Recurring)

• The page was received (Section 6.6).

Two Short Tones

• A unit-to-unit call was received (Section 6.6).

Five Beeps

• The paged radio received the page and acknowledged it (Section 6.6).

• The message that was sent has been received and acknowledged (Section 6.7).

• The status condition that was sent has been received and acknowledged (Section 6.8).

Four Beeps

• The emergency alarm condition was acknowledged (Section 6.9).

• Four low beeps indicate the call back mode (the system is no longer busy).

Содержание 5300 ES Series















































































































































Результаты поиска

Содержание 5300 ES Series

Отзывы:

Похожие инструкции для 5300 ES Series

Бренды по названию

Популярные бренды

E.F. Johnson Company 5300 ES Series, Руководство по эксплуатации

Результаты поиска

Содержание 5300 ES Series

Отзывы:

Похожие инструкции для 5300 ES Series

Бренды по названию

Популярные бренды