E.F. Johnson Company 5300 ES Series Скачать руководство пользователя страница 21

Страница: 21 / 142

March 2008

5300 ES Series Mobile Radio Operating Manual

1-3

General

• Predefined status conditions (up to eight) can be sent to a dispatcher (P25 mode only)

• OTAR (Over-The-Air-Rekeying) compatible (P25 channels only).

• Keypad programming with password access (Federal Government users only)

1.3

SMARTNET / SmartZone Features

The following SMARTNET/SmartZone features are available:

• Up to 512 or 864 talk groups programmable (channels select talk groups) depending on

option enabled

• Group, Enhanced Private Conversation™, standard Private Conversation, and

Telephone calls

• Emergency alarms to alert a dispatcher of emergency conditions

• Emergency calls for high priority system access

• Failsoft operation on a predefined conventional channel if trunked system fails

• Priority group calls detected while listening to other group calls when scanning

• Call Alert™ (send and receive pages)

• Predefined messages (up to 16) can be sent to a dispatcher

• Predefined status conditions (up to eight) can be sent to a dispatcher

• Dynamic regrouping (dispatcher can automatically gather users on a channel to receive

a message)

• Roaming (SmartZone only)

• Announcement Group

1.4

Project 25 Trunked Features

The following P25 features are available:

• Up to 864 talk groups programmable (channels select talk groups) depending on option

enabled

• Group and Unit Calls

• Telephone calls with overdialing

Содержание 5300 ES Series















































































































































Результаты поиска

Содержание 5300 ES Series

Отзывы:

Похожие инструкции для 5300 ES Series

Бренды по названию

Популярные бренды

E.F. Johnson Company 5300 ES Series, Руководство по эксплуатации

Результаты поиска

Содержание 5300 ES Series

Отзывы:

Похожие инструкции для 5300 ES Series

Бренды по названию

Популярные бренды