E.F. Johnson Company 5300 ES Series Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 142

background image

5-2

5300 ES Series Mobile Radio Operating Manual

Conventional Features

Busy Indicator - With scanning disabled, note if the multi-function indicator on the
front panel is steady green. If it is green, a carrier is being detected, so the channel may
be busy. If it is not, the channel is not being used and a call can be transmitted.

Monitor Mode - There may be times when the busy indication is displayed even
though no one is using the channel. Monitoring should then be performed by disabling
Call Guard squelch (or group ID detect on P25 channels). This is usually done by
selecting the Monitor Mode (see following) or by the Normal/Selective option switch
(see Section 5.4.1).

5.2

Monitor Mode

The monitor mode unsquelches the receiver and monitors the channel even if a carrier is
not detected. Other features of this mode are as follows:

• Call Guard (CTCSS/DCS) squelch is disabled on analog channels and NAC and group

ID detect are disabled on P25 (conventional) channels.

• Busy Channel Lockout is overridden (see next section).

• Scanning temporarily halts.

The Monitor Mode operates as follows:

1

To monitor the transmit frequency for activity before transmitting, briefly press the
MON option switch. The display then indicates “MON” (see Figure 2.3). The receiver
unsquelches and noise is heard even if carrier not present.

2

To monitor the receive frequency instead, press and hold the MON option switch until a
tone sounds (approximately two seconds). This can be used, for example, to improve
reception if intermittent squelching is making a weak message difficult to understand.

3

To disable the monitor mode and return to normal operation, press the MON option
switch again.

If off-hook detection is enabled, taking the microphone off-hook monitors the receive
frequency similar to Step 2. However, the receiver unsquelches only if a carrier is detected
(see Section 4.9). Pressing the SEL SQ option switch disables Call Guard squelch/P25
group ID detect but not scanning and P25 NAC detect (see Section 5.4).

«
...
52
53
54
55
56
...
»

Содержание 5300 ES Series















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5300 ES Series

Badradio SR-300

Бренд: Hama Страницы: 3

Бренд: Midland Страницы: 20

Бренд: Rassbach Communications Страницы: 5

Бренд: Hytera Страницы: 47

Бренд: Magnavox Страницы: 20

Бренд: Meinberg Страницы: 22

Бренд: PNI Страницы: 132

Бренд: AcuRite Страницы: 16

Бренд: Ritron Страницы: 2

TOYOTA CQ-MS7920A

Бренд: Panasonic Страницы: 24

Бренд: Vertex Standard Страницы: 6

Бренд: Motorola Страницы: 166

Бренд: Barrett Страницы: 164

Бренд: Icom Страницы: 32

Бренд: Icom Страницы: 53

Бренд: Icom Страницы: 70

Бренд: Denver Electronics Страницы: 5

Бренд: Denver Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды