E.F. Johnson Company 5300 ES Series Скачать руководство пользователя страница 20

Страница: 20 / 142

1-2

5300 ES Series Mobile Radio Operating Manual

March 2008

General

• Emergency calls for high priority system access

• Priority (standard) and Radio Wide scan modes with user programmable scan lists

• User selectable high and low power output

• Surveillance mode

• Time-out timer

• Power up password to prevent unauthorized use.

• Programmable and user adjustable tone volume

• Programmable minimum volume level

• Operates on both wide and narrow band channels

1.2

Conventional Features

The following Conventional features are available:

• Up to 512 or 864 channels or talk groups programmable depending on option enabled

• Repeater talk-around

• Carrier or Call Guard

(CTCSS/DCS) controlled squelch on analog channels, NAC and

talk group IDs on P25 channels

• Normal/selective squelch selectable by option switch

• Monitor mode selectable by option switch

• Time out penalty and conversation timers

• Dual priority channel sampling when scanning (analog and digital channels)

• Busy channel lockout (transmit disable on busy)

• Unit calls on P25 channels

• Telephone calls on P25 channels with overdial

• Emergency alarms and calls to alert a dispatcher of an emergency condition (analog

emergency available).

• Automatic Number Identification (ANI) on analog channels

• MDC 1200 ANI and Emergency Alert support

• Call Alert™ on P25 channels (send and receive pages)

• Predefined messages (up to 16) can be sent to a dispatcher (P25 mode only)

Содержание 5300 ES Series















































































































































Результаты поиска

Содержание 5300 ES Series

Отзывы:

Похожие инструкции для 5300 ES Series

Бренды по названию

Популярные бренды

E.F. Johnson Company 5300 ES Series, Руководство по эксплуатации

Результаты поиска

Содержание 5300 ES Series

Отзывы:

Похожие инструкции для 5300 ES Series

Бренды по названию

Популярные бренды