E.F. Johnson Company 5300 ES Series Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 142

background image

7-6

5300 ES Series Mobile Radio Operating Manual

Parms Fail - The checksum of the profile / user parameters does not match the calculated
checksum. This indicates that there is an error in the parameters file. This message only
occurs if the redundant copy of the parameters is also corrupt or is unable to be used.

Rekey Fail - This error indicates a failure in a rekeying process.

Rx Only - The selected channel is Rx only.

Sts Failed - No acknowledgement was received while sending a status report.

Timeout - A time out has occurred in attempting the current function.

Too Hot - The radio has passed the TOO HOT temperature threshold. Under these
conditions the radio will not allow Tx.

Tx Timeout - The Tx time-out timer has expired and Tx has been terminated.

VOLTAGE HI - The input voltage to the radio is too high.

VOLTAGE LO - The input voltage to the radio is too low.

Write Fail - The radio is unable to write to the EEPROM.

Zone Fail - The radio has been programmed with more zones than its options allow.

7.3

System Operator Programming

As noted previously, programming determines the availability and specific operation of
many features. This usually refers to the programming performed by your system operator
when the radio was set up, not to any programming that a user can perform. If a feature is
controlled by a front panel option switch and that switch is not available, the feature is
probably not available.

An exception is Keypad Programming which can allow the user to reprogram several
conventional channel parameters. Refer to Section 5.14 for more information.

7.4

Speaking Into Microphone

For best results, hold the microphone about 1-2 inches from your mouth and speak at a
normal conversational level. Do not shout since it distorts your voice and does not increase
range.

«
...
104
105
106
107
108
...
»

Содержание 5300 ES Series















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5300 ES Series

Бренд: Baofeng Страницы: 7

Бренд: RACOM Страницы: 16

Бренд: Navman Страницы: 52

Бренд: oticon Страницы: 2

Бренд: Entel Страницы: 20

Бренд: Pure Digital Страницы: 18

Бренд: Jensen Страницы: 14

Бренд: MAJORITY Страницы: 20

Бренд: Exalt Страницы: 86

Бренд: Hannlomax Страницы: 2

Бренд: Tecsun Страницы: 24

Бренд: MAJORITY Страницы: 24

Бренд: Monitor Audio Страницы: 36

Бренд: Garmin Страницы: 48

Бренд: Century Mark IV Страницы: 6

Бренд: Garmin Страницы: 57

Бренд: Steren Страницы: 45

Бренд: Transonic Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды