DSC Envoy NT9010 Скачать руководство пользователя страница 7

Страница: 7 / 64

S e c t i o n 1 . 1 : I n t r o d u c t i on

System Supervision Features

The NT9010 continuously monitors a number of possible trouble conditions including:

• AC power failure (system enters “Sleep” mode on loss of AC power for longer than

30 seconds)

• Trouble by zone

• Fire trouble

• Telephone line trouble

• Low battery condition

• Remote sounder supervisory

• Loss of internal clock

• Tamper by zone

• Failure to communicate

• Improper zone placement

False Alarm Prevention Features

• Audible exit delay

• Audible exit fault

• Urgency on entry delay

• Quick exit

• Swinger shutdown

• Recent closing transmission

• Communication delay

• Rotating keypress buffer

Additional Features

• Keypad activated alarm output and communicator test

• Keypad lockout

• 128 event buffer, time and date stamped

• Uploading/downloading capability

1.1.4 Additional

Devices

WLS904-433 Wireless Motion Detector

The wireless motion detector can be used to provide wireless interior protection. The unit
comes with four AAA batteries

WLS904PL-433 Wireless Motion Detector with Pet Immunity

The wireless motion detector can be used to provide wireless interior protection.

WLS906-433 Wireless Smoke Detector

The wireless smoke detector can be used to provide wireless smoke detection. The unit
comes with six AA batteries

WLS912-433 Wireless Glassbreak Detector

The wireless glassbreak detector can be used to provide wireless glassbreak detection. The
unit comes with three AA batteries

Содержание Envoy NT9010

































































Результаты поиска

Содержание Envoy NT9010

Отзывы:

DSC Envoy NT9010, Руководство по установке, Страница: 7 / 64

Результаты поиска

Содержание Envoy NT9010

Отзывы: