manualshive.com logo in svg

DSC Envoy NT9010, Руководство по установке, Страница: 25 / 64

Поделиться
Скачать
DSC Envoy NT9010 Скачать руководство пользователя страница 25

S e c t i o n   2 . 2 :   C ha ng i n g  H o w  t h e   N T 9 0 1 0   W o r k s   F o r  U s e r s

2 1

NOTE:

 If you enable the Bell Squawk on Arming/Disarming option (section

[014], option [1]), the bell will sound arm/disarm bell squawks for all access
codes, regardless of the programming for attribute [7] (see 2.2.5 Arming and
Disarming Options on page 22).

Installer’s Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Section [006]
Master code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Section [007]
Maintenance Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Section [008]
Master Code Not Changeable. . . . . . . . . . . . . . . . . . . . . .Section [015], Option [6]
Code Required for Bypassing Section [015], Option [5]Telephone Access CodeSection 
[807]-[020]

2.2.3 Voice Prompt 

Interface

You can customize the voice prompt interface for the NT9010 users by turning individual
prompts on or off, and by changing how the NT9010 system announces the current time.

To have the NT9010 system announce the time in am/pm format (e.g. 9:00am), turn on
the 

Clock is AM/PM

 option. To have the system announce the time in 24-hr format (e.g.

21:00), turn on the 

Clock is 24 Hour

 option.

The NT9010 system is designed to be easy to use by reminding users of available com-
mands. For example, after a user accesses the system, they can press [

✱

] and the NT9010

system will announce the [

✱

] commands that are available. 

You can avoid confusing users by turning on only the prompts that apply to the system
you are installing. The options in sub-section [004] only affect the NT9010 system [

✱

]

command prompts: if a prompt is disabled, users will still be able to enter the command it
refers to.

Sub-section [003] determines which Status prompts the user will hear. If an option is
“ON”, the system will announce the prompt when the appropriate condition is present. If
an option is “OFF”, the system will not announce the prompt if the condition is present.
For example, if you turn off the “Zone Tamper” prompt, when a zone is tampered on the
system, the NT9010 system will not announce it to the user.

You can also have the NT9010 system announce the names of zones that are opened or
closed by turning on the 

Verbal Chime

 option. When this option is turned on, if the 

Ver-

bal Chime for Zone Openings

 is also enabled, whenever a zone with the Chime attribute

enabled is opened, a series of beeps will sound and the NT9010 will prompt (for example):

“Front Door”

If the 

Verbal Chime for Zone Closings

 is enabled, the NT9010 system will announce the

zone label when the zone is closed. See also 

[*] [4] Door Chime On/Off

 on page 26.

You can create custom labels for the system and for each zone in the

 Labels

 programming

area. Please see 

2.1.5 Programming Audio Labels

 on page 16 for more information.

Clock is AM/PM  . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [807]-[002], Option [1]
System Status Prompts  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [807]-[003]
[

✱

] Command Prompts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [807]-[004]

Door Chime Zone Attribute. . . . . . . . . . . . . . . .  Sections [101] to [132], Option [3]
Verbal Chime Enabled/Disabled. . . . . . . . . . . . . . . . . . . . .Section [017], Option [2]
Verbal Chime for Zone Openings  . . . . . . . . . . . . . . Section [807]-[002], Option [2]

Содержание Envoy NT9010

































































Отзывы:

Нет отзывов