Dover HEIL LIBERTY TP1L-SM-0520 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 136

background image

Issued May 2020

Lift Arm

Copyright 2020, Heil Environmental
Printed in the U.S.A.

Lift Arm

47

LIFT ARM PREVENTIVE MAINTENANCE CHART

Maintenance performed on a regular schedule is preventive maintenance. Normal maintenance intervals are based on an
8-hour day and average operating conditions. Severe use or adverse conditions make it necessary to do this maintenance
more frequently.

Watch the

Preventive Arm Lift Maintenance

video on the

Heil Service Shack (https://www.heil.com/heil-service-

.

REF NO.

ACTIVITY

INTERVAL

SERVICE/CHECK

1

Grease Lift

(20 hrs)

See the

Python Lift Lubrication Guide

or the

lubrication decal on the lift arm.

2

Check Pin Retaining Bolts –
Tighten

Weekly
(40 hrs)

Check for broken bolts. This may indicate bearing or pin
damage. Replace the bolt and the bearing and pin
retained by the bolt. Use anti-seize compound on any pins
or bearings that are replaced.

3

Hydraulic Plumbing

Weekly
(40 hrs)

Check for damage, worn, or leaking hoses, tubes or
fittings. Replace as necessary. NOTE: Do not replace
steel tubes with hoses.

4

Cycle Times (900
maximum RPM while
operating lift)

Weekly
(40 hrs)

Check lift operation. Normal engine RPMs should not
exceed 900. The lift operates at approximately 7 – 8
second cycle time. Cycle times includes grab, lift, lower
and release.

5

Check Mounts

Weekly
(40 hrs)

Make sure chassis rail is undamaged.
Make sure chassis bolts are present and tight.
Check brackets for cracks.
Make sure lift bolts are present and secure.

6

Check Lift Mount Base
Bolts

Weekly
(40 hrs)

Visually inspect mounting bolts for security and
movement. Check the nuts and bolts to make sure the
weld is secure. See

Check Lift and Torque Mount Base

for bolt replacement instructions.

7

Lift Stress or Weld Cracks

Weekly
(40 hrs)

Check lift for any structural cracks or cracks in the areas
of welds. Cracks must be ground out and repaired. If
cracking continues replace the affected parts. See

and Weld Cracks Decision Tree

in this section.

8

Grabber Assembly with Belt

Weekly
(40 hrs)

Inspect belt condition for wear, cuts or damage. Replace
if present.

9

Hoses

Weekly
(40 hrs)

Check for tears, wear or holes and replace as necessary.

10

Fiber Guards

Weekly
(40 hrs)

Check for tears or holes and replace as necessary.

11

Shaft Retainer Bolts

Monthly
(200 hrs)

Make sure both pins are present and tight. If one pin
fails, replace both pins.
Make sure the collar key is present. If one fails.

12

Grabber Cylinder Pivot Bolt

Monthly
(200 hrs)

Check for tightness.

13

Hydraulic Relief Valves

Twice
Yearly
(1000 hrs)

Check main relief and port reliefs for proper settings. For
more information see

Lift Control Valve Pressure

Adjustments

in this section.

46

48

61

55

«
...
51
52
53
54
55
...
»

Содержание HEIL LIBERTY TP1L-SM-0520









































































































































Отзывы:

Нет отзывов

Похожие инструкции для HEIL LIBERTY TP1L-SM-0520

Бренд: ZOLL Страницы: 5

Бренд: Accu-Chek Страницы: 3

Бренд: iBin Страницы: 2

Бренд: Raymarine Страницы: 70

Бренд: Bard Страницы: 36

Бренд: Bard Страницы: 2

Бренд: Bard Страницы: 30

Бренд: Bard Peripheral Vascular Страницы: 44

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Olsen Страницы: 4

Dominator Series

Бренд: Falcon Страницы: 31

Бренд: Fakir Страницы: 22

Бренд: Fayat Group Страницы: 50

Бренд: Halyard Страницы: 88

Бренд: Xycom Страницы: 99

Бренд: Hagerman Страницы: 4

Бренд: hager Страницы: 2

TECSHOW QUAD SPIDER 60

Бренд: Ampro Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды