Dover HEIL LIBERTY TP1L-SM-0520 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 136

background image

Issued May 2020
Lift Arm

Copyright 2020, Heil Environmental

Printed in the U.S.A.

Lift Arm

48

CHECK LIFT AND TORQUE MOUNT BASE BOLTS

When the Lift Base Mounting bolts weld is cracked, you must replace the bolts and nuts. The goal of this torque method is
to achieve a 59,000lb clamp load consistently. A torque multiplier is not accurate enough at the values required. This
method (torque/turn) is accurate and repeatable.

This method is required for field installation where proper torquing equipment may not be available. It also allows proper
bolt torquing using standard wrenches and “cheater” bars.

A. Tools Required

Figure 12. Lift Mount Base

Quantity

Tool

1

Torque wrench (1” and 5/8” sockets)

1

Combination wrench (1” and 5/8”)

1

Welding equipment

1

Personal protective equipment

B. Parts Required

See Parts Manual for replacement parts.

C.Before Replacing Lift Mount Bolts

1. Visually inspect the lift mount bolts on both the street side and

curb side. See the illustration for locations.

2. Make sure the bolts are secure and there is no movement.

3. Make sure welded bolts do not have cracks.

4. If any lift mount bolt is loose, cracked or broken, replace all

bolts. Use only the parts specified. Lower grade parts are not
acceptable.

5. After torquing, bolts and nuts cannot be reused. To install and

torque bolts, complete section D below.

D.Replace Lift Mount Bolts

1. Make sure the threads on both the bolt and nut are dry (no

lubrication) before installation.

2. Install bolt into lift base and lift mount brackets.

3. Thread nuts onto bolts and hand tighten.

4. Use a torque wrench with a combination wrench to tighten the nut to 100 ft-lbs., holding bolt-head and turning nut.

5. Mark nut, washer and lift base with a paint market at a corner.

6. Count around 3-1/2 nut flats and mark the center of the nut, washer and lift base.

«
...
52
53
54
55
56
...
»

Содержание HEIL LIBERTY TP1L-SM-0520









































































































































Отзывы:

Нет отзывов

Похожие инструкции для HEIL LIBERTY TP1L-SM-0520

Бренд: Eagle Страницы: 3

Бренд: Warehouse-lighting Страницы: 3

Бренд: Eagle Group Страницы: 8

Бренд: E2S Страницы: 5

ENET-232 Series

Бренд: National Instruments Страницы: 105

Бренд: National Instruments Страницы: 22

Бренд: Nautilus Страницы: 17

Бренд: National Instruments Страницы: 6

Бренд: Major tech Страницы: 12

Бренд: Planmeca Страницы: 56

Бренд: DBI SALA Страницы: 16

Бренд: Velp Scientifica Страницы: 20

Бренд: Danfoss Страницы: 10

Бренд: ETC Страницы: 7

Бренд: PROEL Страницы: 16

Бренд: OEM Страницы: 164

Бренд: Cerillo Страницы: 2

Бренд: Future light Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды