Dover HEIL LIBERTY TP1L-SM-0520 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 136

background image

Issued May 2020
General Information

Copyright 2020, Heil Environmental

Printed in the U.S.A.

General Information

28

PROXIMITY SWITCH TROUBLESHOOTING

When one or more of a unit’s functions do not operate properly and there are proximity switches in the circuits of the unit
for these functions, refer to the following table as a guide to find the problem(s).

NOTICE

Heil proximity switches have a Light Emitting Diode (LED) on the switch to indicate that the switch is sensing metal. The
light changes color when the switch senses metal. Green indicates the switch is ON. Yellow indicates the switch senses
metal. Some proximity switches only have the yellow light.

Proximity Switch Troubleshooting Table

Probable Cause

Remedy

Loose or corroded electrical connections.

Replace the electrical connections.

Damaged Switch
A. Cracked Ferrite core causing the fine internal

wire to break.

B. Cracked Ferrite core – but wire is not broken –

the sensitivity of switch will increase which
causes sensing distance to increase or switch
work intermittently as the temperature changes.

DO NOT strike switch to make it work.
DO NOT damage the switch when you adjust it.
DO NOT adjust switch too close to the metal it is sensing.

Voltage spikes from truck chassis electrical system
will break down the internal electronics of the
proximity switch.

1. Make sure the power source from the chassis

manufacturer is clean.

2. The body electrical system is protected from voltage

spikes.

Improper Sensing Range

Adjust proximity switches to sense metal as follows:

If the controller input light stays on when a switch is
unplugged (the signal wire is ca12V DC)

Check the proximity switch electrical circuits for the source of
the problem.

If proximity switch LED light is NOT ON.

1. Check the fuse relay block (Half/Packs with IFM

controllers). The fuse/relay box is located in the cab. Or
Check the in-line fuses (Side Loaders with IFM controllers).
The in-line fuses are located in the cab.

2. Unplug proximity switch.
3. Check the power wire (terminal C) for +12 VDC with a

multi-meter.

4. Check ground signal with multi-meter for continuity to

chassis ground.

5. Check the signal wire for continuity to appropriate

controller input terminal. See Service Manual.

6. If all three (3) wires are good, replace the proximity switch.

«
...
32
33
34
35
36
...
»

Содержание HEIL LIBERTY TP1L-SM-0520









































































































































Отзывы:

Нет отзывов

Похожие инструкции для HEIL LIBERTY TP1L-SM-0520

Бренд: ZOLL Страницы: 344

Бренд: ABB Страницы: 9

Бренд: Hammer Strength Страницы: 18

Бренд: Ofa Bamberg Страницы: 80

Бренд: Omlet Страницы: 60

Бренд: YASKAWA Страницы: 40

Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology...

Бренд: M-Audio Страницы: 25

MCX-C15 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 114

Бренд: Qlight Страницы: 4

Бренд: DAAB Страницы: 12

Ti-Max NLX nano

Бренд: NSK Страницы: 38

Бренд: Sensio Страницы: 3

BinTrac HouseLINK HL-10P

Бренд: herdstar Страницы: 8

Бренд: Pepperl+Fuchs Страницы: 60

Бренд: Samson Страницы: 20

Бренд: Partec Страницы: 26

Compumotor 6200

Бренд: Parker Страницы: 45

Бренд: Nautilus Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды