manualshive.com logo in svg

Dover HEIL LIBERTY TP1L-SM-0520, Руководство по обслуживанию, Страница: 22 / 136

Поделиться
Скачать
Dover HEIL LIBERTY TP1L-SM-0520 Скачать руководство пользователя страница 22

Issued May 2020
General Information

Copyright 2020, Heil Environmental

Printed in the U.S.A.

General Information

16

STORING REFUSE IN THE BODY

Heil does not recommend storing refuse in the body overnight. The different types of debris and corrosive elements usually
collected can cause severe corrosion inside the body decreasing the life of your body. This corrosion can affect unloading
and decrease the structural life of the body. In addition, storing refuse in the body overnight can increase the risk of fire.

MAINTENANCE/LUBRICATION INFORMATION

Before performing maintenance, check the work area carefully to find all the hazards present and make sure all safe
guards or safety devices are in place to protect all persons and equipment involved.

WINCH GEAR OIL

When the unit has a winch option, check the level of the winch’s gear oil every 40 hours of operation. Fill as needed with
AGMA Grade 5 EP (90wt.) for an 8,000 lb. winch and AGMA Grade 7 EP (140 wt.) for a 12,000 lb. winch. 

GREASE LUBRICANT RECOMMENDATION

Use a grease gun. Before engaging grease gun, clean the fitting. Always pump enough grease to purge the joint of
contaminated grease and wipe off the excess. Lubricate a unit as given on the lubrication decal on the unit and in the 

Body

Lubrication Guide

 paragraph of this section.

Use grade NLG1000 grease or equivalent.

OIL LUBRICANT RECOMMENDATION

Use only non-detergent engine oil to lubricate all moveable mechanical parts not furnished with grease fittings. Apply
sufficient oil to give good lubrication, but do not bathe parts in oil. Always wipe off excess oil.

HYDRAULIC OIL SPECIFICATIONS

Hydraulic fluid is one of the most important component in hydraulic system. It transmits power, provides lubrication and
cooling function and has following features:

High viscosity index 

Long service life

Outstanding cold temperature flow properties

Fast water separation

Excellent anti-wear performance

Long term oxidation stability

Superior rust and corrosion protection

Exceptional shear stability / filterability

Excellent thermal and hydrolytic stability

Anti-foam characteristics

High performance of air release characteristics

Current Heil standard hydraulic oil is Shell Tellus S2 VX 32. Please see product TDS and MSDS for more detail information
about it. We strongly recommend to use it on Heil products to get best system performance and oil service life.

The following oils can be used on Heil products if Heil standard hydraulic oil (Shell Tellus S2 VX 32) is not available. But
system performance and/or oil service life may be compromised. 

Castrol Dual Range HV 32

Chevron Rando HDZ 32

Mobil DTE 10 Excel 32

79

Содержание HEIL LIBERTY TP1L-SM-0520









































































































































Отзывы:

Нет отзывов