Dover HEIL LIBERTY TP1L-SM-0520 Скачать руководство пользователя страница 87

Страница: 87 / 136

Issued May 2020

Maintenance and Adjustment

Maintenance and Adjustment

10 POINT AUTO LUBE (CONTINUED)

C. Maintenance

(a)How to Refill Lubrication Cylinder

Raise the body and secure with body props.

Tailgate must be closed and locked in position.

Rotate the packer so that the lubrication cylinder is in a convenient access position, such as front street side.

Turn ignition off

To fill the reservoir, locate the grease fittings on the inside end and the ¼” grease line coming from the inside end of
the cylinder.

As you add grease, you must allow hydraulic oil to flow out the opposite end. This can be done in a number of ways:

1) With the packer in MANUAL mode to operate the tailgate, engine off but ignition switch on, hold down the

tailgate “down” control. While the valve is trying to lower the tailgate, the oil can flow out of the cylinder,
through the valve and into the tank

2) With the engine off, but ignition switch on and the PTO engaged, place a jumper wire from tailgate “down” to

the TO in the lower junction box

3) Hook up a temporary hose to the oil end of the lube cylinder and let it drain into the tank.

(b) Using a grease gun filled with NLGI 000 grease; fill the cylinder/reservoir from the grease zerk on the opposite end.

This grease is light and thin so that it can pass through lubrication lines.

(d) Operate the tailgate open/close mechanism several times to check for leaks and broken hoses.

Содержание HEIL LIBERTY TP1L-SM-0520










































































































Результаты поиска

Содержание HEIL LIBERTY TP1L-SM-0520

Отзывы:

Dover HEIL LIBERTY TP1L-SM-0520, Руководство по обслуживанию, Страница: 87 / 136

Результаты поиска

Содержание HEIL LIBERTY TP1L-SM-0520

Отзывы: