Dover HEIL LIBERTY TP1L-SM-0520 Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 136

background image

Issued May 2020
Body and Tailgate

Copyright 2020, Heil Environmental

Printed in the U.S.A.

Body and Tailgate

72

TAILGATE UNLATCH LIMIT SWITCH (N.C.)

The Tailgate Unlatch Limit Switch (N.C.) is non-adjustable and mounted on the tailgate with the striker mounted on the
tailgate hinge. It is activated by breaking contact with the striker. When the tailgate latch is released, causing the striker to
move, this switch interrupts an electrical circuit causing an alarm to sound, warning the operator that the tailgate is not fully
closed and latched.

CAUTION

If the tailgate unlatch limit switch does not activate the alarm, DO NOT operate the truck. Further troubleshooting is
required.

PACKER REVERSING LIMIT SWITCH (N.C.)

The Packer Reversing Limit Switch (N.C.) is non-adjustable located under the body behind the packer actuator plate. This
switch is used to signal when to reverse the direction of the packer paddle in the automatic packing condition. It should be
mounted so that the reversing motion of the packer paddle occurs before the left or right hand packer cylinder completely
bottoms out. If this switch does not work, the body full alarm will sound.

«
...
76
77
78
79
80
...
»

Содержание HEIL LIBERTY TP1L-SM-0520









































































































































Отзывы:

Нет отзывов

Похожие инструкции для HEIL LIBERTY TP1L-SM-0520

Бренд: UnionSpecial Страницы: 56

Бренд: MAHLE Страницы: 21

Бренд: CAIRE Страницы: 2

SATURA SPOT LED PRO

Бренд: Elation Страницы: 41

Бренд: Tapco Страницы: 16

Бренд: Zenbooth Страницы: 40

Visium CytAssist

Бренд: 10x Genomics Страницы: 51

Chromium X Series

Бренд: 10x Genomics Страницы: 5

Бренд: NCR Страницы: 20

Бренд: DARAY Страницы: 32

Body Armor Night Splint

Бренд: Darco Страницы: 2

Бренд: MacDon Страницы: 74

Бренд: Salter Страницы: 18

Бренд: Salter Страницы: 42

Бренд: Salter Страницы: 47

Бренд: Salter Страницы: 35

Бренд: Salter Страницы: 40

M-041 INDOOR CROSS

Бренд: Salter Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды