Dover HEIL LIBERTY TP1L-SM-0520 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 136

background image

Issued May 2020

Body and Tailgate

Copyright 2020, Heil Environmental
Printed in the U.S.A.

Body and Tailgate

71

BODY-UP LIMIT SWITCH

The Body-Up Limit Switch is a non-adjustable normally closed (N.C.) switch and is located on the left body prop bracket
with the striker located on the body above the switch. This limit switch turns on an alarm when the body is raised off the
chassis.

CAUTION

If the Body-Up Limit Switch does not activate the alarm, DO NOT the truck. Further troubleshooting is required.

The Body-Up Limit Switch is a non-adjustable normally closed (N. C.) switch and is mounted on a bracket off the right rear
hinge plate. It is activated by making contact with the lower flange of the body long member. This switch limits how high the
body will raise by interrupting the power to the UP solenoid on the body/packer valve. This switch should be activated
before either body hoist cylinder bottoms out or before the body exceeds a 40 degree dump angle.

Although the Body-Up Limit Switch is non-adjustable, it is mounted on a slotted bracket enabling the switch to slide up or
down if some adjustment is required. If the switch is not activated when the body is raised, adjust the switch by loosening
the bolts holding the switch to the bracket and slide the switch down on the bracket.

«
...
75
76
77
78
79
...
»

Содержание HEIL LIBERTY TP1L-SM-0520









































































































































Отзывы:

Нет отзывов

Похожие инструкции для HEIL LIBERTY TP1L-SM-0520

Бренд: Makerfire Страницы: 10

Бренд: Waterwise Страницы: 12

Бренд: ParaBody Страницы: 38

Бренд: Latchways Страницы: 80

Бренд: Kapriol Страницы: 28

Бренд: Eagle Eye Страницы: 21

Бренд: Labomed Страницы: 67

Бренд: HABYS Страницы: 16

Бренд: Yamaha Страницы: 4

Бренд: Wacker Neuson Страницы: 120

Бренд: Yamaha Страницы: 126

DM 2000 Version 2

Бренд: Yamaha Страницы: 8

Бренд: York Страницы: 16

i.Profiler plus

Бренд: Zeiss Страницы: 66

Бренд: IKEA Страницы: 24

Novation Launchkey Mini

Бренд: Focusrite Audio Engineering Страницы: 36

Бренд: Vitax Страницы: 12

500 FleetBroadband

Бренд: Sailor Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды