Dover HEIL LIBERTY TP1L-SM-0520 Скачать руководство пользователя страница 108

Страница: 108 / 136

Issued May 2020
Body Controller Software

Printed in the U.S.A.

BODY CONTROLLER SOFTWARE

102

OPTION SETTING SCREEN

Press the OK button to change option setting. Press the escape button to exit screen

Figure 44. Option Configuration

J1939 Baud Rate

- 250/500 - Setting should match chassis baud

rate. Does not require added hardware.

Hot Shift P

TO - On/Off - ON, Enables Hot shift PTO functionality

and PTO Solenoid Output. Only used when Hot shift PTO in
installed.

Low Oil Detection

- On/Off - ON, Enables Low Oil Detection and

Pump shutdown when oil level is low. Requires installation of level
sensor in oil tank.

Oil Temp Detection

- On/Off - ON, Enables Oil Temp Detection

and Pump shutdown when oil temp is high.Requires installation of
temperature transducer in oil tank.

No Side Door

- On/Off (Default ON) - ON, Disables side door

interlock and pump shutdown. To be turned OFF when optional
side access door is not installed.

Grabber Open lock

- On/Off - ON, Enables interlock preventing

grabber from opening with the lift raised. Requires additional
hardware to determine lift raised position.

Lift Raise lock

- On/Off - ON, Enables interlock preventing lift from raising with grabber open. Requires additional

hardware to determine lift raised and grabber closed.

Hyd Hopper Cover

- On/Off - ON, Enables circuits for optional hydraulic hopper cover. Only used when Hydraulic Hopper

option in installed.

Hopper Cover Indicator

- On/Off - ON, Enables circuits for hopper cover indicator. When included with Lift Raise Interlock

prevents lift from raising with cover closed. Only used when Hydraulic Hopper option in installed.

Enable Lift Stow

- On/Off - ON, Enables automatic stow of lift when grabber open button is pressed. Does not require

added hardware.

Operation Speed Limit

– 7 mph/12 mph - Sets the maximum vehicle speed for lift, hoist and tailgate operation. Does not

require added hardware.

Enable Out of Dimension Signal

- On/Off - ON, Enables the out of dimension signal indicating a lift or body component is

not properly positioned for transit. Does not require added hardware.

Enable Dual JStick

- On/Off - ON, Enables functionality for a secondary lift control joystick. Requires added hardware.

Содержание HEIL LIBERTY TP1L-SM-0520










































































































Результаты поиска

Содержание HEIL LIBERTY TP1L-SM-0520

Отзывы:

Похожие инструкции для HEIL LIBERTY TP1L-SM-0520

Бренды по названию

Популярные бренды

Dover HEIL LIBERTY TP1L-SM-0520, Руководство по обслуживанию

Результаты поиска

Содержание HEIL LIBERTY TP1L-SM-0520

Отзывы:

Похожие инструкции для HEIL LIBERTY TP1L-SM-0520

Бренды по названию

Популярные бренды