Dormakaba ED250 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 60

background image

36

ED250

01-2018

DL4614-080

dormakaba ED250 IG Service Manual

Chapter 17

Parameter

Value

range

Units

Factory

setting Description

Factory setting level

32

1 - 2

1

1

Parameter

SL

is used to determine what data will be reset during factory setting

process.

Standard factory settings
•  Program switches OFF.
•  Door closed.
•  Press 4 button keypad down button

for > 8 s.

1.  All parameters reset to factory settings.
2.  Procedure completed when "8" on 2 digit displays blinks twice.
3.  Installed upgrade cards remain valid and do not require reinstallation.
4.  Learning cycle required.

2

Extended factory settings

•  Program switches OFF.
•  Door closed.
•  Press 4 button keypad down button

for > 8 s.

1.  All parameters reset to factory settings.
2.  Procedure completed when "8" on 2 digit displays blinks twice.
3.  Installed upgrade cards deleted from operator memory.
4.  Parameter

SL

automatically reset to 1.

5. Control unit and upgrade cards can be used independently (delivery status).
6. Learning cycle required..

Opening angle

1.  Door opening angle set during learning cycle is displayed.
2.  Opening angle can only be changed during learning cycle.
3.  Due to installation and parameter tolerances, display value may not match actual door

position.

33

0 - 110

°

Door closer mode

34

0 - 1

1

0

1. Automatic mode. This mode is applicable whenever door is mainly opened

automatically and where motion detectors are installed.

2.  Mode is optimized for high frequency use.
3.  Full energy upgrade card provides for higher door opening and closing speeds.
4.  In case door is blocked during a closing cycle, operator reverses automatically.
5.  Driving phase is optimized to provide reliable closing cycles.
6.  Keep closed force (wind load control) parameter

FH

and Push & Go function

parameter

PG

are only available in automatic mode.

1

1. Manual mode. This mode is applicable whenever door is mainly used manually

and only rarely automatically.

2.  In case door is blocked during a closing cycle, door will stop at its current position.
3.  Driving phase optimized for manual opening cycles.
4.  Power assist function parameter

hf

is only available in manual mode.

Power assist activation angle (v1.7)

1. Setting of door activation angle for Power assist function (

hF

).

2. Higher settings of

hA

result in better spring force compensation for easier manual

opening.

3. Power assist function is more sensitive the smaller the activation angle.

35

1 - 5

°

3

17.3.1 Driving parameters detail

(Continued)

«
...
34
35
36
37
38
...
»

Содержание ED250





























































Отзывы:

Нет отзывов

Похожие инструкции для ED250

POWER TIG 210EXT

Бренд: R-Tech Страницы: 27

Бренд: Reflex Страницы: 26

TIG 160 DC Lift

Бренд: GYS Страницы: 20

Бренд: Saimatic Страницы: 40

Бренд: GYS Страницы: 53

Бренд: Parweld Страницы: 16

3VL9300-3HE0 Series

Бренд: Siemens Страницы: 7

Бренд: Siemens Страницы: 7

3VM9 17-0FK2 Series

Бренд: Siemens Страницы: 10

Бренд: Siemens Страницы: 10

3VA9137-0FK Series

Бренд: Siemens Страницы: 14

Бренд: SEA Страницы: 2

Бренд: Dormakaba Страницы: 10

Бренд: WIELANDER+SCHILL Страницы: 28

Бренд: Lincoln Electric Страницы: 25

Бренд: aoyue Страницы: 6

Бренд: Fimer Страницы: 36

Бренд: F.F. Group Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды