Dormakaba ED250 Скачать руководство пользователя страница 26

Страница: 26 / 60

ED250

01-2018

DL4614-080

dormakaba ED250 IG Service Manual

Chapter 16

ED250 Parameter

A156.19 standard

Parameter

Function

Factory

setting

Adjustment range

Para. Requirement

Opening speed

Swing door opening speed

19°/s

Note 1

ED250

8°/s - 60°/s

Note 2

4.2

Opening

Doors shall open from closed to back check or

80°, whichever occurs first, in 3 seconds or

longer as required in Table I.

Total opening time to 90° shall be as in Table II

(next page) If door opens at more than 90°, it

shall continue at the same rate as backcheck

speed.

Backcheck

Checking or slowing down of

door speed before door being

fully opened.

10°

5° - 40°

4.2

Backcheck shall not occur before 60° opening.

Closing speed

Swing door closing speed,

automatic mode.

19°/s

Note 1

ED250

28/s - 60°/s

Note 2

4.4

Closing

Doors shall close from 90° to 10° in 3 s or

longer as required in Table I (next page).

Doors shall close from 10° to fully closed in not

less than 1.5 s.

Hold open

time

Hold open time

5 s

5 s - 30 s

4.3

Time delay

When powered open, the door shall remain

open at the fully opened position for not less

than 5 s. Exception: when push-pull activation

is used, the door shall remain at the fully

opened position for not less than 3 s.

Reference

ED250 service

manual for

parameter

detail.

Support for manual mode in

door closed position.

4.5

Doors shall open:

• With a manual force not to exceed 15 lb f to

release a latch if equipped with a latch.

•  To set a door in motion 30 lb f .
•  To fully open the door 15 lb f .
•  Forces shall be measured 1" fro m latch edge of

door.

Adjustment, door activation

angle.

Power assist function.

Static force

in opening

direction

Static force on door closing

edge in opening direction.

13.5 lb f

4.5 lb f - 33.7 lb f

Reduced in low

energy mode.

4.5

The force required to prevent a stopped door

from opening or closing shall not exceed

15 lb f measured 1" from latch edge of the

door at any point during opening or closing.

Static force

in closing

direction

Static force on door closing

edge in closing direction.

13.5 lb f

4.5 lb f

33.7 lb f

Reduced in low

energy mode.

4.5

16.2 A156.19 Low energy power operated doors

The following table references portions of content from ANSI/BHMA A156.19. Refer to the standard, available
through ANSI or BHMA for additional information. Standard material reprinted with BHMA permission

16.2.1 Door measurements, low energy power operated door

Note 1: Speed may be slower after learning cycle

completed.

Note 2: Speed limited to 27° s in low energy mode.

Содержание ED250





























































Результаты поиска

Содержание ED250

Отзывы:

Похожие инструкции для ED250

Бренды по названию

Популярные бренды

Dormakaba ED250, Руководство по обслуживанию

Результаты поиска

Содержание ED250

Отзывы:

Похожие инструкции для ED250

Бренды по названию

Популярные бренды