Dormakaba ED250 Скачать руководство пользователя страница 24

Страница: 24 / 60

ED250

11-2017

DL4614-080

dormakaba ED250 IG Service Manual

Chapter 15

CAUTION

Learning cycle must be performed while
motor is cold!

CAUTION

Door must not be manually moved or held in
position during the learning cycle!

CAUTION

Verify that the following parameters have
been set (Para. 17, Parameters):

• AS

, Installation type

• rd

, Reveal depth

• Tb

, Door width

• dL

, Door type (double doors only)

TIPS AND RECOMMENDATIONS

During learning cycle:

• Safety sensors and activators, are switched off to

insure learning cycle sequence is not interrupted.

• Operator functions are deactivated.

Step 2

Set program switch to CLOSE position.

Rotating "0" and an O indicate operator

is ready for learning cycle.

Step 3

Press

Press and hold down button until display

changes.

• Door performs several movements

and display shows a sequence of
symbols.

• Movements of door must not be

interrupted!

WARNING

No personnel or objects must be in range of
door motion!

Step 1

Secure motion range of door.

Display indicates door is at 70° position

and is waiting for door opening angle to

be set.

Step 4

Manually move door to desired

maximum opening angle

(maximum door angle: 110°).

Step 5

Press

Momentarily press down button to

continue learning cycle.

CAUTION

Insure there are no obstacles to door movement!

• Door performs several movements

and display shows a sequence of
symbols.

• Movements of door must not be

interrupted!

• Spring tension is too low if door

stops and display shows a small
rotating "o" and an "F".

Step 6

f spring tension is too low::

• Turn off power and push or let door

close.

• Increase spring tension (Chapter 14),

turn on power and restart learning
cycle (Step 3).

Door will complete learning cycle.
• Display with two horizontal bars

indicate operator is ready for
operation.

Step 7

Press

Momentarily press down button to cycle

door.

Step 8

Following automatic learning cycle,

actual forces on door, and door

opening and closing times must be

measured and changed if necessary

to insure compliance with ANSI/

BHMA standards, reference Chapter

16.

Step 9

Set program switch to Auto.

15 Learning cycle

Содержание ED250





























































Результаты поиска

Содержание ED250

Отзывы:

Похожие инструкции для ED250

Бренды по названию

Популярные бренды

Dormakaba ED250, Руководство по обслуживанию

Результаты поиска

Содержание ED250

Отзывы:

Похожие инструкции для ED250

Бренды по названию

Популярные бренды